Yamaha SR10LE Скачать руководство пользователя страница 25

Страница: 25 / 52

0747-766

Spark Plugs



NOTE: Always use the recom-

mended spark plugs in the engine.

See the appropriate specifications

sheet for correct spark plug gap.

1. Disconnect the main harness from the

ignition coils; then remove the ignition

coils from the cylinder head cover.

2. Remove the three spark plugs.



NOTE: Prior to installing the spark

plugs, check the gap between the

electrode and ground strap. The

clearance should be 0.7-0.8 mm

(0.028-0.031 in.).

3. Install new spark plugs. Tighten to

1.3 kg-m (9.4 ft-lb).

4. Install the ignition coils onto the cyl-

inder head cover making sure they

are fully seated. Connect the main

harness to the ignition coils.

5. Install the hood and access panels.

Checking/Adjusting

Valve Clearance

After 40,000 km (25,000 miles), valve

clearance should be checked and adjusted

as necessary.



NOTE: Take the snowmobile to an

authorized Yamaha Snowmobile

dealer for inspection and service.

This service is at the discretion and

expense of the snowmobile owner.

Battery

These sealed batteries after being in ser-

vice require regular cleaning and charg-

ing in order to deliver peak performance

and maximum service life. The following

procedure is recommended for cleaning

and maintaining sealed batteries. Always

read and follow instructions provided

with battery chargers and battery prod-

ucts.



NOTE: Battery maintenance may

be done by the snowmobile owner if

qualified to do so. If the owner does

not feel qualified, take the snowmo-

bile to an authorized Yamaha Snow-

mobile dealer for this service. This

service is at the discretion and

expense of the snowmobile owner.

CAUTION

If the coolant is below the neck and if

coolant has been added, immediately

inspect for leakage and/or damage. If

leakage or damage is detected, take

the snowmobile to an authorized

Yamaha Snowmobile dealer for ser-

vice. If not under warranty, this ser-

vice is at the discretion and expense

of the snowmobile owner.

CAUTION

If adjusting spark plug gap is neces-

sary, do not use the center electrode

as a leverage point. Damage to the

plug may occur.

CAUTION

It is critical that the checking/adjust-

ing valve clearance be done at the

recommended intervals or severe

engine damage may occur.

! WARNING

Improper handling or connecting of a

battery may result in severe injury

including acid burns, electrical burns,

or blindness as a result of an explo-

sion. Always remove rings and

watches. Any time service is per-

formed on a battery, the following

must be observed: keep sparks, open

flame, cigarettes, or any other flame

away. Always wear safety glasses.

Protect skin and clothing when han-

dling a battery. When servicing a bat-

tery in an enclosed space, keep the

area well-ventilated.

Содержание SR10LE





















































Результаты поиска

Содержание SR10LE

Отзывы:

Бренды по названию

Популярные бренды

Yamaha SR10LE, Руководство оператора

Результаты поиска

Содержание SR10LE

Отзывы:

Бренды по названию

Популярные бренды