Yamaha SR10LE Скачать руководство пользователя страница 5

Страница: 5 / 52

General Information

Snowmobile

Identification

The snowmobile has two important iden-

tification numbers. The Vehicle Identifi-

cation Number (VIN) is stamped into the

tunnel near the right-side footrest and on

a decal beneath the seat. The decal also

displays pertinent production informa-

tion. The Engine Serial Number (ESN) is

stamped into the crankcase of the engine.

0726-383

These numbers are required by the dealer

to complete warranty claims properly. No

warranty will be allowed by Yamaha Inc.

if the engine serial number or VIN is

removed or mutilated in any way.
Always provide the snowmobile name,

VIN, and ESN when contacting an autho-

rized Yamaha Snowmobile dealer for

parts, service, accessories, or warranty. If

the complete engine must be replaced,

ask the dealer to notify Yamaha for cor-

rect registration information.

Control Locations

Shown are the typical control locations

for Yamaha snowmobiles. Location of a

specific control will vary according to

model.

0747-829

Gasoline-Oil

Recommended Gasoline

The recommended gasoline to use in

these snowmobiles is 87 octane regular

unleaded. In many areas, oxygenates are

added to the gasoline. Oxygenated gaso-

lines containing up to 10% ethanol are

acceptable gasolines.
When using ethanol blended gasoline, it is

not necessary to add a gasoline antifreeze

since ethanol will prevent the accumula-

tion of moisture in the fuel system.

Recommended Engine Oil

The recommended oil to use is Semi-

Synthetic Yamalube OW-30 oil.

The engine oil should be changed every

4000 km (2500 miles) before prolonged

storage and the oil filter should be

changed every 20,000 km (12,500 miles).

Filling Gas Tank

Since gasoline expands as its temperature

increases, the gas tank must be filled to

its rated capacity only. Expansion room

must be maintained in the tank particu-

larly if the tank is filled with cold gaso-

line and then moved to a warm area.

CAUTION

Any oil used in place of the recom-

mended oil could cause serious

engine damage

Содержание SR10LE





















































Результаты поиска

Содержание SR10LE

Отзывы:

Похожие инструкции для SR10LE

Бренды по названию

Популярные бренды

Yamaha SR10LE, Руководство оператора

Результаты поиска

Содержание SR10LE

Отзывы:

Похожие инструкции для SR10LE

Бренды по названию

Популярные бренды