Yamaha SR10LE Скачать руководство пользователя страница 42

Страница: 42 / 52

DRIVE CLUTCH/DRIVEN

CLUTCH OFFSET

— If premature

drive belt wear is experienced or if the

drive belt turns over, offset must be

checked. Also, offset must be checked

whenever either the drive clutch or

driven clutch is serviced.

Checking Offset

1. Remove the left-side access panel;

then move the console up and out of

the way.

2. Remove the drive belt.



NOTE: Use a straightedge that is

approximately 470 mm (18.5 in.)

long, 20 mm (0.79 in.) wide, and 4

mm (0.16 in.) thick.

3. Place the straightedge along the

back side of the drive clutch; then

measure the offset (a) between the

driven clutch and the straightedge.

Sheave offset must be within 13.0-

16.0 mm (0.51-0.63 in.). If adjust-

ment is needed, proceed to step 4.

SNO-324



NOTE: The straightedge must

extend beyond the front edge of the

drive clutch.

4. If offset adjustment needs to be

made, remove the driven clutch and

add shims (p/n 8JP-RA449-00: 2

mm, 8JP-RA448-00: 1 mm) to

increase the offset or remove shims

to decrease the offset.

5. Once the correct offset is reached,

install driven clutch and tighten cap

screw to 6.4 kg-m (46 ft-lb).



NOTE: When adjusting the driven

clutch, the clutch free play (clear-

ance) should be adjusted.

6. Using a feeler gauge, measure the

clutch free play (clearance). Free

play (a) should be within 1.0-2.0

mm (0.04-0.08 in.). If adjustment

needs to be made proceed to step 7.

SNO-325

7. Remove the driven clutch cap screw

and washer; then add shims (p/n

8JP-RA447-00: 2 mm, 8JP-RA446-

00: 1 mm, 8JP-RA433-00: 0.5 mm).

8. Install the driven clutch cap screw

and washer. Tighten to 6.4 kg-m (46

ft-lb).

GASOLINE

— For optimum perfor-

mance, use 87 octane (minimum) gaso-

line.

Содержание SR10LE





















































Результаты поиска

Содержание SR10LE

Отзывы:

Бренды по названию

Популярные бренды

Yamaha SR10LE, Руководство оператора

Результаты поиска

Содержание SR10LE

Отзывы:

Бренды по названию

Популярные бренды