Yamaha PJP-MC24 Скачать руководство пользователя страница 8

Страница: 8 / 92

Notations Used in This Manual

Abbreviations

The following product names are abbreviated throughout the manual.

•  YAMAHA PJP-MC24: This product
•  IP Phone Conference System PJP-100H, PJP-50R: ProjectPhone
•  Microsoft

Windows

: Windows

• 10BASE-T (100BASE-TX) cable: LAN cable

Configuration examples

Examples of configured items such as IP addresses, domain names, and URLs, are only

being used to help clarify explanations. When configuring this product, set up the

configuration based on the actual network that this product will be connected to.

Technical terms and understanding

Users need to have extensive knowledge of networks and the Internet to use this product
properly. The manuals included with this product do not provide this knowledge. For more
information please refer to commercial guides and reference books.

Trademark acknowledgments

• Ethernet is a registered trademark of Xerox Corporation.
• Microsoft, Windows, and Microsoft Excel are either registered trademarks or

trademarks of Microsoft Corporation in the United States and/or other countries.

Содержание PJP-MC24





























































































Результаты поиска

Содержание PJP-MC24

Отзывы:

Похожие инструкции для PJP-MC24

Бренды по названию

Популярные бренды

Yamaha PJP-MC24, Инструкция по эксплуатации

Результаты поиска

Содержание PJP-MC24

Отзывы:

Похожие инструкции для PJP-MC24

Бренды по названию

Популярные бренды