Yamaha PJP-MC24 Скачать руководство пользователя страница 72

Страница: 72 / 92

rfo

g D

ice

ain

ten

Utilizing the latest functions (revision upgrade)

(Continued)

Upgrading to the Latest

Revision

Obtain the latest firmware using a PC, etc., and
transfer the firmware to the product via TFTP to
upgrade the program to the latest revision.

1. Check the latest revision number

Check Revision of the System Information window.

Opening the System Information window:

Click the following items in the Web interface:



System Information in the main window while

logged in as an administrator

2. Obtain the latest firmware

Access the ProjectPhone support page from a PC

to obtain the latest firmware.

ProjectPhone support page

http://www.yamaha.co.jp/projectphone/

.Permit TFTP server access

Permit the product to access the TFTP server on
the

TFTP Server Settings

window.

Opening the TFTP Server Settings

window

Click the following items in the Web interface:



Maintenance

on the main window while logged

in as an administrator.



Change

under

TFTP Server Settings

Содержание PJP-MC24





























































































Результаты поиска

Содержание PJP-MC24

Отзывы:

Похожие инструкции для PJP-MC24

Бренды по названию

Популярные бренды

Yamaha PJP-MC24, Инструкция по эксплуатации

Результаты поиска

Содержание PJP-MC24

Отзывы:

Похожие инструкции для PJP-MC24

Бренды по названию

Популярные бренды