Yamaha PJP-MC24 Скачать руководство пользователя страница 78

Страница: 78 / 92

Tro

les

oti

When LEDs are off or blinking

Symptom



Cause



Solution

All LEDs

do not light.

The PJP-MC24 is not turned on.

Turn the power switch on.

The power cord is
not connected.

Make sure that the power cord is secured

firmly in the power socket.

The main or
line circuit breakers
have been tripped.

•

If the breaker is switched off, switch it

on.

•

If the breaker is switched on, switch it

off and then back on again.

There is a power outage.

Wait until power returns.

The outlet is not receiving power.
(when other devices cannot be
used either).

•

If other devices are not functioning

either, have the outlet or wiring fixed.

•

If other devices are functioning on the

same outlet, have the PJP-MC24 fixed.

The LINK LED at the

LAN port does not

turn on.

The PC or hub is
turned off.

Confirm that the PJP-MC24 and the
devices connected to it are on. Even if
a device is connected correctly to the LAN
port, the LAN LED will not light unless the
connected device is turned on.

The PJP-MC24 is not connected
properly.

Remove all cords and then reinsert them,
making sure that they click into place.

The cable in use is
not a LAN cable.

•

Make sure that you are not using an

ISDN cable (the connectors look exactly
the same, so it can be hard to tell the
difference).

•

Try switching to a different LAN cable.

The PC LAN (network) card is
not functioning properly, or its
connection mode is not
compatible with the PJP-MC24.

•

If other devices are not functioning

either, have the outlet or wiring fixed.

•

If other devices are functioning on the

same outlet, have the PJP-MC24 fixed.

All LEDs are

lighted

Immediately after the power
has been turned on (normal
operation).

Wait for about three seconds for loading

to finish.

The PJP-MC24 is broken.

Have the PJP-MC24 repaired.

Содержание PJP-MC24





























































































Результаты поиска

Содержание PJP-MC24

Отзывы:

Похожие инструкции для PJP-MC24

Бренды по названию

Популярные бренды

Yamaha PJP-MC24, Инструкция по эксплуатации

Результаты поиска

Содержание PJP-MC24

Отзывы:

Похожие инструкции для PJP-MC24

Бренды по названию

Популярные бренды