Yamaha PJP-MC24 Скачать руководство пользователя страница 73

Страница: 73 / 92

rfo

g D

ice

ain

ten

4. Transfer the firmware to the product

Note

Once the revision upgrade is started, never perform

any operation until the upgrade is completed and the

product is restarted.If the upgrade is interrupted, the

product may become unusable.In this case, you must

bring the product to YAMAHA for repair.

Once the revision upgrade is completed, the product

restarts automatically. When the product is restarted,

all communication is disconnected.

Never disconnect the LAN cable while the revision

upgrade is still in progress.Doing so may render the

product unusable, in which case you must bring the

product to YAMAHA for repair.

Follow the operating steps below:

Launch Command Prompt on a Windows

PC where the product has been permitted

to access the TFTP server (previous

page).

If you are using a Windows XP PC, click

Start

click

All Programs

, click

Accessories

, and

then select

Command Prompt

Enter and execute the following

command:

tftp -i [IP address of the product]
put [File name]exec

-i

Entry example:

tftp -i 192.168.100.101 put pjp_mc24.
bin exec

-i

The revision upgrade is started.

It takes several minutes before the product

is upgraded.

The ALARM, STATUS and CONFERENCE
LEDs turn on one by one while the product is
being upgraded.Do not turn off the power to the
product while any of the LEDs is lit.

Once the revision upgrade is completed,

the product is restarted.
In

Revision

of the

System Information

window,

confirm that the revision number has been updated.

Opening the

System Information

window:

Click the following items in the Web interface:



System Information

in the main window while

logged in as an administrator

Содержание PJP-MC24





























































































Результаты поиска

Содержание PJP-MC24

Отзывы:

Похожие инструкции для PJP-MC24

Бренды по названию

Популярные бренды

Yamaha PJP-MC24, Инструкция по эксплуатации

Результаты поиска

Содержание PJP-MC24

Отзывы:

Похожие инструкции для PJP-MC24

Бренды по названию

Популярные бренды