background image

 

Operation

 

37

 

arm or leg. Then install the lock plate on
the other end of the lanyard into the en-
gine stop switch.

WARNING

 

EWM00120 

 

 

Attach the engine stop switch lanyard
to a secure place on your clothing, or
your arm or leg while operating.

 

 

Do not attach the lanyard to clothing
that could tear loose. Do not route the
lanyard where it could become entan-
gled, preventing it from functioning.

 

 

Avoid accidentally pulling the lanyard
during normal operation. Loss of en-
gine power means the loss of most
steering control. Also, without engine
power, the boat could slow rapidly. This
could cause people and objects in the

 

boat to be thrown forward.

 

3.

Turn the main switch to “

” (on).

4.

Turn the main switch to “

” (start),

and hold it for a maximum of 5 seconds.

5.

Immediately after the engine starts, re-
lease the main switch and allow it to re-
turn to “

” (on).

CAUTION:

 

ECM00191 

 

 

Never turn the main switch to “

(start) while the engine is running.

 

 

Do not keep the starter motor turning
for more than 5 seconds. If the starter
motor is turned continuously for more
than 5 seconds, the battery will be
quickly discharged, thus making it im-
possible to start the engine. The starter
can also be damaged. If the engine will
not start after 5 seconds of cranking,
return the main switch to “

” (on), wait

10 seconds, then crank the engine

 

again.

ON

START

OFF

ON

START

OFF

ZMU04589

START

ON

ZMU04590

Содержание LZ150D



























































































Отзывы: