Yamaha LZ150D Скачать руководство пользователя | Manualshive

Страница: 19 / 90

background image

Basic components

14

EMU26211

Neutral throttle lever

To open the throttle without shifting into ei-
ther forward or reverse, put the remote con-
trol lever in the neutral position and lift the
neutral throttle lever.

NOTE:

The neutral throttle lever will operate only
when the remote control lever is in neutral.
The remote control lever will operate only
when the neutral throttle lever is in the closed

position.

EMU26230

Free accelerator

To open the throttle without shifting into ei-
ther forward or reverse, push the free accel-

erator button and move the remote control
lever.

NOTE:

●

The free accelerator button can only be
used when the remote control lever is in
the neutral position.

●

After the button is pushed, the throttle be-
gins to open after the remote control lever
is moved at least 35°.

●

After using the free accelerator, return the
remote control lever to the neutral position.
The free accelerator button will return au-
tomatically to its set position. The remote
control will then engage forward and re-

verse normally.

EMU25970

Throttle friction adjuster

A friction device provides adjustable resis-
tance to movement of the throttle grip or the
remote control lever, and can be set accord-
ing to operator preference.
To increase resistance, turn the adjuster
clockwise. To decrease resistance, turn the
adjuster counterclockwise.

WARNING

EWM00030

Do not overtighten the friction adjuster. If

1. Neutral interlock trigger

1. Fully open
2. Fully closed

1. Fully open
2. Fully closed
3. Free accelerator

1

3

2

ZMU04575

«
...
17
18
19
20
21
...
»

Содержание LZ150D



























































































Отзывы:

Нет отзывов

Похожие инструкции для LZ150D

Бренд: MSI Страницы: 19

Бренд: Texas Instruments Страницы: 19

Бренд: Navia Страницы: 26

35891900 Series

Бренд: PC Partner Страницы: 16

Venus VNS563-4GD

Бренд: Diamond Systems Страницы: 43

Бренд: QDI Страницы: 20

Fatal1ty Z87 Killer Series

Бренд: ASROCK Страницы: 102

Бренд: DFI Страницы: 130

P55 GD80 - Motherboard - ATX

Бренд: MSI Страницы: 150

Бренд: Intel Страницы: 12

Бренд: Analog Devices Страницы: 6

126791-HMC764LP6C

Бренд: Analog Devices Страницы: 18

Бренд: H-Tec Страницы: 28

Бренд: TransCore Страницы: 40

Бренд: Analog Devices Страницы: 7

Spacewalker AV40

Бренд: Shuttle Страницы: 81

Бренд: ASROCK Страницы: 237

Бренд: MSI Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды