Yamaha LZ150D Скачать руководство пользователя

Страница: 50 / 90

Operation

EMU28060

Cruising in shallow water

The outboard motor can be tilted up partially
to allow operation in shallow water.

EMU28090

Power trim and tilt models / power tilt
models

The outboard motor can be tilted up partially
to allow operation in shallow water.

WARNING

EWM00660

●

Place the gear shift in neutral before
setting up for shallow water cruising.

●

Return the outboard motor to its normal
position as soon as the boat is back in

deeper water.

CAUTION:

ECM00260

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-

ting up for and cruising in shallow water.
Otherwise severe damage from overheat-

ing can result.

EMU28183

Procedure for power trim and tilt / power
tilt models

Place the gear shift lever in neutral.

Slightly tilt the outboard motor up to the
desired position using the power trim / tilt
switch.

ZMU04603

ZMU03999

ZMU04588

ZMU01935

Содержание LZ150D



























































































Результаты поиска

Содержание LZ150D

Отзывы:

Похожие инструкции для LZ150D

Бренды по названию

Популярные бренды

Yamaha LZ150D, Руководство пользователя

Результаты поиска

Содержание LZ150D

Отзывы:

Похожие инструкции для LZ150D

Бренды по названию

Популярные бренды