Yamaha LZ150D Скачать руководство пользователя | Manualshive

Страница: 46 / 90

background image

Operation

41

angle can cause loss of control.

●

Use the power tilt switch located on the
bottom engine cowling (if equipped)
only when the boat is at a complete

stop with the engine off.

Adjust the outboard motor trim angle using
the power trim and tilt switch.

To raise the bow (trim-out), press the switch
“

” (up).

To lower the bow (trim-in), press the switch
“

” (down).

Make test runs with the trim set to different
angles to find the position that works best for
your boat and operating conditions.

NOTE:

To adjust the trim angle while the boat is
moving, use the power trim and tilt switch lo-
cated on the remote control device or tiller

handle, if equipped.

EMU27911

Adjusting boat trim

When the boat is on plane, a bow-up attitude
results in less drag, greater stability and effi-
ciency. This is generally when the keel line of
the boat is up about 3 to 5 degrees. With the
bow up, the boat may have a greater tenden-
cy to steer to one side or the other. Compen-
sate for this as you steer. The trim tab can
also be adjusted to help offset this effect.
When the bow of the boat is down, it is easier
to accelerate from a standing start onto
plane.

1. Power trim and tilt switch

1. Power trim and tilt switch

ZMU04601

DN

UP

1

1. Power trim and tilt switch

UP

DN

ZMU04615

1

«
...
44
45
46
47
48
...
»

Содержание LZ150D



























































































Отзывы:

Нет отзывов

Похожие инструкции для LZ150D

Бренд: Ublox Страницы: 2

Бренд: u-blox Страницы: 24

Бренд: MSI Страницы: 35

Бренд: Intel Страницы: 113

VECTOR 1 MOTHERBOARD

Бренд: Vector Graphic Страницы: 14

Бренд: IBASE Technology Страницы: 62

Бренд: Advantech Страницы: 5

TPS5420EVM-175 SWIFT

Бренд: Texas Instruments Страницы: 16

Бренд: DG Страницы: 18

Бренд: C&T Solution Страницы: 90

Бренд: Alinx Страницы: 29

Бренд: IEI Technology Страницы: 164

Бренд: Daewoo Страницы: 39

Бренд: Gigabyte Страницы: 53

Бренд: Supermicro Страницы: 119

Бренд: ComNav Technology Страницы: 28

Бренд: C-Control Страницы: 8

Бренд: Lantronix Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды