background image

 

29

 

Operation

 

EMU26901

 

Installation

CAUTION:

 

ECM00110 

 

Incorrect engine height or obstructions
to smooth water flow (such as the design
or condition of the boat, or accessories
such as transom ladders or depth finder
transducers) can create airborne water
spray while the boat is cruising. Severe
engine damage may result if the motor is
operated continuously in the presence of

 

airborne water spray.

NOTE:

 

During water testing check the buoyancy of
the boat, at rest, with its maximum load.
Check that the static water level on the ex-
haust housing is low enough to prevent wa-
ter entry into the powerhead, when water
rises due to waves when the outboard is not

 

running.

 

EMU26910

 

Mounting the outboard motor

WARNING

 

EWM00820 

 

 

Overpowering a boat could cause se-
vere instability. Do not install an out-
board motor with more horsepower
than the maximum rating on the capac-
ity plate of the boat. If the boat does not
have a capacity plate, consult the boat
manufacturer.

 

 

The information presented in this sec-
tion is intended as reference only. It is
not possible to provide complete in-
structions for every possible boat and
motor combination. Proper mounting
depends in part on experience and the

 

specific boat and motor combination.

WARNING

 

EWM00830 

 

Improper mounting of the outboard mo-
tor could result in hazardous conditions
such as poor handling, loss of control, or
fire hazards. Observe the following:

 

 

For permanently mounted models, your
dealer or other person experienced in
proper rigging should mount the motor.
If you are mounting the motor yourself,
you should be trained by an experi-
enced person.

 

 

For portable models, your dealer or oth-
er person experienced in proper out-
board motor mounting should show

 

you how to mount your motor.

 

Mount the outboard motor on the center line
(keel line) of the boat, and ensure that the
boat itself is well balanced. Otherwise the
boat will be hard to steer. For boats without
a keel or which are asymmetrical, consult
your dealer.

 

1. Center line (keel line)

1

ZMU01873

Содержание LZ150D



























































































Отзывы: