Yamaha LZ150D Скачать руководство пользователя

Страница: 23 / 90

Basic components

EMU26340

Tilt support lever for power trim and
tilt or hydro tilt model

To keep the outboard motor in the tilted up
position, lock the tilt support lever to the
clamp bracket.

EMU26391

Top cowling lock levers

To remove the outboard motor top cowling,
pull up the front and rear lock levers. Then lift
off the cowling. When the cowling, check to
be sure it fits properly in the rubber seal.
Then lock the cowling again by moving the
levers downward.

CAUTION:

ECM00550

The air intake grille on the top cowling is
not designed as a handle and could break

if used as such.

EMU26460

Flushing device

This device is used to clean the cooling wa-

1. Trim tab
2. Bolt
3. Cap

1. Tilt support lever

ZMU01863

ZMU03979

1. Top cowling lock lever(s)

1. Air intake grille
2. Top cowling lock lever(s)

ZMU03986

ZMU04437

Содержание LZ150D



























































































Результаты поиска

Содержание LZ150D

Отзывы:

Похожие инструкции для LZ150D

Бренды по названию

Популярные бренды

Yamaha LZ150D, Руководство пользователя

Результаты поиска

Содержание LZ150D

Отзывы:

Похожие инструкции для LZ150D

Бренды по названию

Популярные бренды