Yamaha FZ6Y Скачать руководство пользователя страница 82

Страница: 82 / 106

PERIODIC MAINTENANCE AND ADJUSTMENT

7-39

5. While supporting the brake caliper

and slightly lifting the wheel, pull
the wheel axle out.

TIP

A rubber mallet may be useful to tap the
wheel axle out.

6. Push the wheel forward, and then

remove the drive chain from the
rear sprocket.

TIP

The drive chain does not need to be
disassembled in order to remove and
install the rear wheel.

7. Remove the wheel.

NOTICE:

not apply the brake after the
wheel has been removed to-
gether with the brake disc, oth-
erwise the brake pads will be
forced shut.

[ECA11071]

EAU32943

To install the rear wheel

1. Install the wheel and the brake cal-

iper bracket by inserting the wheel
axle from the right-hand side.

TIP

●

Make sure that the slot in the brake
caliper bracket is fit over the retain-
er on the swingarm.

●

Make sure that there is enough
space between the brake pads be-
fore installing the wheel.

2. Install the drive chain onto the rear

sprocket, and then adjust the drive
chain slack. (See page 7-26.)

3. Install the axle nut.
4. Lower the rear wheel so that it is

on the ground, and then put the
sidestand down.

5. Tighten the axle nut to the speci-

fied torque.

1. Locknut
2. Drive chain slack adjusting bolt

3. Wheel axle

4. Brake caliper bracket
5. Brake caliper

1. Retainer

2. Slot

U4S812E0.book Page 39 Monday, October 6, 2008 4:06 PM

Содержание FZ6Y











































































































Результаты поиска

Содержание FZ6Y

Отзывы:

Похожие инструкции для FZ6Y

Бренды по названию

Популярные бренды

Yamaha FZ6Y, Руководство пользователя

Результаты поиска

Содержание FZ6Y

Отзывы:

Похожие инструкции для FZ6Y

Бренды по названию

Популярные бренды