Yamaha FZ6Y Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 106

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-26

7

EAU22760

Drive chain slack

The drive chain slack should be
checked before each ride and adjusted
if necessary.

EAU22793

To check the drive chain slack

1. Place the motorcycle on the cen-

terstand.

2. Shift the transmission into the neu-

tral position.

3. Spin the rear wheel several times

to locate the tightest portion of the
drive chain.

4. Measure the drive chain slack as

shown.

5. If the drive chain slack is incorrect,

adjust it as follows.

EAU34313

To adjust the drive chain slack

1. Loosen the axle nut and the lock-

nut on each side of the swingarm.

2. To tighten the drive chain, turn the

drive chain slack adjusting bolt on
each side of the swingarm in direc-
tion (a). To loosen the drive chain,
turn the adjusting bolt on each side
of the swingarm in direction (b),
and then push the rear wheel for-
ward.

NOTICE:

Improper drive

chain slack will overload the en-
gine as well as other vital parts
of the motorcycle and can lead
to chain slippage or breakage.
To prevent this from occurring,
keep the drive chain slack with-
in the specified limits.

[ECA10571]

TIP

Using the alignment marks on each
side of the swingarm, make sure that
both chain pullers are in the same posi-
tion for proper wheel alignment.

3. Tighten the locknuts, then the axle

nut to their specified torques.

1. Drive chain slack

Drive chain slack:

45.0–55.0 mm (1.77–2.17 in)

1. Locknut

2. Drive chain slack adjusting bolt
3. Axle nut

4. Alignment marks

5. Chain puller

Tightening torques:

Locknut:

16 Nm (1.6 m·kgf, 11 ft·lbf)

Axle nut:

120 Nm (12.0 m·kgf, 85 ft·lbf)

U4S812E0.book Page 26 Monday, October 6, 2008 4:06 PM

«
...
67
68
69
70
71
...
»

Содержание FZ6Y











































































































Отзывы:

Нет отзывов

Похожие инструкции для FZ6Y

Бренд: DAELIM Страницы: 2

V 7 CAFE CLASSIC

Бренд: MOTO GUZZI Страницы: 147

Бренд: RDMOTO Страницы: 2

Spyder RT Series

Бренд: Can-Am Страницы: 52

Бренд: Malaguti Страницы: 242

Бренд: Honda Страницы: 127

Бренд: SCHUBERTH Страницы: 43

Бренд: Barton Страницы: 35

Бренд: Kinderkraft Страницы: 36

Бренд: R&G Страницы: 19

Бренд: R&G Страницы: 20

Бренд: R&G Страницы: 20

Бренд: R&G Страницы: 22

TERMOSCUD R224X

Бренд: tucanourbano Страницы: 4

Бренд: Cagiva Страницы: 124

Бренд: Piaa Страницы: 17

QuickShifter easy

Бренд: Healtech Страницы: 3

iLogger easy iLE-1-KIT

Бренд: Healtech Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды