Yamaha FZ6Y Скачать руководство пользователя страница 80

Страница: 80 / 106

PERIODIC MAINTENANCE AND ADJUSTMENT

7-37

EAU24312

Replacing the license plate
light bulb

1. Remove the license plate light unit

by removing the screws.

2. Remove the socket (together with

the bulb) by pulling it out.

3. Remove the burnt-out bulb by pull-

ing it out.

4. Insert a new bulb into the socket.
5. Install the socket (together with the

bulb) by pushing it in.

6. Install the license plate light unit by

installing the screws.

EAU24360

Front wheel

EAU43091

To remove the front wheel

WARNING

EWA10821

To avoid injury, securely support the
vehicle so there is no danger of it
falling over.

1. Place the vehicle on the center-

stand.

2. Loosen the front wheel axle pinch

bolt, then the wheel axle and the
brake caliper bolts.

1. Screw

2. License plate light unit

1. License plate light bulb
2. License plate light bulb socket

1. Wheel axle

2. Front wheel axle pinch bolt

U4S812E0.book Page 37 Monday, October 6, 2008 4:06 PM

Содержание FZ6Y











































































































Результаты поиска

Содержание FZ6Y

Отзывы:

Похожие инструкции для FZ6Y

Бренды по названию

Популярные бренды

Yamaha FZ6Y, Руководство пользователя

Результаты поиска

Содержание FZ6Y

Отзывы:

Похожие инструкции для FZ6Y

Бренды по названию

Популярные бренды