Yamaha FZ6Y Скачать руководство пользователя страница 81

Страница: 81 / 106

PERIODIC MAINTENANCE AND ADJUSTMENT

7-38

3. Remove the brake caliper (togeth-

er with the reflector) on each side
by removing the bolts.

NOTICE:

Do not apply the brake after the
brake calipers have been re-
moved, otherwise the brake
pads will be forced shut.

[ECA11051]

4. Pull the wheel axle out, and then

remove the wheel.

EAU43101

To install the front wheel

1. Lift the wheel up between the fork

legs.

2. Insert the wheel axle.

3. Install the brake caliper (together

with the reflector) on each side by
installing the bolts.

TIP

Make sure that there is enough space
between the brake pads before install-
ing the brake calipers onto the brake
discs.

4. Lower the front wheel so that it is

on the ground, and then put the
sidestand down.

5. Tighten the wheel axle, the front

wheel axle pinch bolt and the
brake caliper bolts to the specified
torques.

6. Push down hard on the handlebar

several times to check for proper
fork operation.

EAU25080

Rear wheel

EAU25151

To remove the rear wheel

WARNING

EWA10821

To avoid injury, securely support the
vehicle so there is no danger of it
falling over.

1. Loosen the axle nut.
2. Place the motorcycle on the cen-

terstand.

3. Remove the axle nut.
4. Loosen the locknut and drive chain

adjusting bolt on each side of the
swingarm.

1. Brake caliper
2. Brake caliper bolt

3. Reflector

Tightening torques:

Wheel axle:

72 Nm (7.2 m·kgf, 52 ft·lbf)

Front wheel axle pinch bolt:

19 Nm (1.9 m·kgf, 13 ft·lbf)

Brake caliper bolt:

40 Nm (4.0 m·kgf, 29 ft·lbf)

1. Locknut

2. Drive chain slack adjusting bolt

3. Axle nut

U4S812E0.book Page 38 Monday, October 6, 2008 4:06 PM

Содержание FZ6Y











































































































Результаты поиска

Содержание FZ6Y

Отзывы:

Похожие инструкции для FZ6Y

Бренды по названию

Популярные бренды

Yamaha FZ6Y, Руководство пользователя

Результаты поиска

Содержание FZ6Y

Отзывы:

Похожие инструкции для FZ6Y

Бренды по названию

Популярные бренды