Yamaha FZ6Y Скачать руководство пользователя страница 59

Страница: 59 / 106

PERIODIC MAINTENANCE AND ADJUSTMENT

7-16

EAU42682

To change the coolant

1. Place the vehicle on the center-

stand and let the engine cool if
necessary.

2. Place a container under the engine

to collect the used coolant.

3. Remove the radiator cap retaining

bolt, radiator cap retainer and radi-
ator cap.

WARNING! Never at-

tempt to remove the radiator
cap when the engine is hot.

[EWA10381]

4. Remove the coolant reservoir cap.

5. Remove the coolant reservoir cov-

er and coolant reservoir by remov-
ing the bolts.

6. Drain the coolant from the coolant

reservoir by turning it upside down.

7. Install the coolant reservoir and its

reservoir cover by placing them in
the original position, and then in-
stalling the bolts.

8. Remove the coolant drain bolt to

drain the cooling system.

9. After the coolant is completely

drained, thoroughly flush the cool-
ing system with clean tap water.

10. Install the coolant drain bolt, and

then tighten it to the specified
torque.

TIP

Check the washer for damage and re-
place it if necessary.

1. Radiator cap retaining bolt
2. Radiator cap

3. Radiator cap retainer

1. Coolant reservoir cap
2. Coolant reservoir

1. Coolant reservoir cover
2. Bolt

1. Coolant drain bolt

U4S812E0.book Page 16 Monday, October 6, 2008 4:06 PM

Содержание FZ6Y











































































































Результаты поиска

Содержание FZ6Y

Отзывы:

Похожие инструкции для FZ6Y

Бренды по названию

Популярные бренды

Yamaha FZ6Y, Руководство пользователя

Результаты поиска

Содержание FZ6Y

Отзывы:

Похожие инструкции для FZ6Y

Бренды по названию

Популярные бренды