Yamaha FX Cruiser WaveRunner 2007 Скачать руководство пользователя страница 7

Страница: 7 / 108

General and important labels

EJU30350

Emission control information

This engine conforms to 2006 U.S. Environ-
mental Protection Agency (EPA) and/or Cali-
fornia Air Resources Board (CARB)
regulations for marine SI engines.
This engine is certified to operate on regular
unleaded gasoline.

EJU30390

Approval label of emission control
certificate

This label is attached to the top of the cylinder
head and to the bulkhead.

EJU30430

Manufactured date label

This label is attached to the top of the cylinder
head.

EJU30440

Star labels

This watercraft is labeled with a California Air
Resources Board (CARB) star label. See be-
low for a description of your particular label.

Emission control information label location

Manufactured date label location

Star label location

UF1Y11E0.book Page 2 Wednesday, August 23, 2006 11:43 AM

Содержание FX Cruiser WaveRunner 2007













































































































Результаты поиска

Содержание FX Cruiser WaveRunner 2007

Отзывы:

Yamaha FX Cruiser WaveRunner 2007, Руководство владельца/оператора, Страница: 7 / 108

Результаты поиска

Содержание FX Cruiser WaveRunner 2007

Отзывы: