Yamaha FX Cruiser WaveRunner 2007 Скачать руководство пользователя страница 50

Страница: 50 / 108

Features and functions

To open the glove compartment, turn the
glove compartment knob, and then lift up the
lid.

To close the glove compartment, lower the lid,
and then turn the glove compartment knob to
lock the lid in place.

EJU31760

Seat storage compartment

The seat storage compartment is located un-
der the rear seat.

To open the seat storage compartment, re-
move the rear seat. (See page 29 for rear seat
removal and installation procedures.)

Glove compartment knob

Glove compartment

Glove compartment:

Capacity:

5.5 L (1.5 US gal) (1.2 Imp.gal)

Load limit:

1.0 kg (2 lb)

Seat storage compartment

Seat storage compartment:

Capacity:

15.0 L (4.0 US gal) (3.3 Imp.gal)

Load limit:

9.0 kg (20 lb)

UF1Y11E0.book Page 45 Wednesday, August 23, 2006 11:43 AM

Содержание FX Cruiser WaveRunner 2007













































































































Результаты поиска

Содержание FX Cruiser WaveRunner 2007

Отзывы:

Yamaha FX Cruiser WaveRunner 2007, Руководство владельца/оператора, Страница: 50 / 108

Результаты поиска

Содержание FX Cruiser WaveRunner 2007

Отзывы: