Yamaha FX Cruiser WaveRunner 2007 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 108

Yamaha FX Cruiser WaveRunner 2007 Скачать руководство пользователя страница 41

Features and functions

36

ahead acceleration when on plane and top
speed are enhanced.
In some conditions, however, the watercraft
may tend to “porpoise” (hop in the water). If
the watercraft is porpoising, select neutral or
bow down.

EJU31360

Handgrip

The handgrip provides a handhold for board-
ing the watercraft and for a spotter when fac-
ing rearward.

FX

FX Cruiser

WARNING

EWJ00020

Do not use the handgrip to lift the water-
craft. The watercraft could fall, which
could result in severe injury.

EJU34860

Reboarding step (for FX Cruiser)

The reboarding step provides a handhold and
footstep for boarding the watercraft.

CAUTION:

ECJ00740

Use the reboarding step only to board the
watercraft in the water. Do not use the re-
boarding step for lifting the watercraft, as
a footstep when the watercraft is on land,
or for any other purpose. The watercraft
can be damaged.

EJU34870

Bow eye

The bow eye is located at the bow of the wa-
tercraft.
The bow eye is used to attach a rope to the
watercraft when transporting, mooring, or
towing it in an emergency.

1

Handgrip

1

Handgrip

1

Reboarding step

1

Bow eye

UF1Y11E0.book Page 36 Wednesday, August 23, 2006 11:43 AM

«
...
39
40
41
42
43
...
»

Содержание FX Cruiser WaveRunner 2007













































































































Отзывы:

Нет отзывов