manualshive.com logo in svg

Yamaha FX Cruiser WaveRunner 2007, Руководство владельца/оператора, Страница: 4 / 108

Поделиться
Скачать
Yamaha FX Cruiser WaveRunner 2007 Скачать руководство пользователя страница 4

Table of contents

General and important labels........... 1

Identification numbers  ....................  1

Primary Identification (PRI-ID) 

number ...........................................  1

Hull Identification Number (HIN) ........  1
Engine serial number  ........................  1

Emission control information  ..........  2

Approval label of emission control 

certificate ........................................  2

Manufactured date label ....................  2
Star labels  .........................................  2

Important labels ..............................  4

Warning labels ...................................  5
Other labels  .......................................  7

Safety information............................. 9

Limitations on who may operate 

the watercraft  ..............................  9

Cruising limitations  .......................  10
Operation requirements  ...............  12
Recommended equipment  ...........  14
Hazard information  .......................  15
Watercraft characteristics .............  15
Water-skiing .................................  17
Rules of the Road  ........................  19
To get more boating safety 

information ................................  23

Enjoy your watercraft 

responsibly ................................  24

Features and functions................... 25

Location of main components  ......  25
Operation of controls and other 

functions ....................................  29

Seats ...............................................  29
Hood ................................................  30
Fuel tank filler cap  ...........................  31
Engine stop switch  ..........................  31
Engine shut-off switch  .....................  31
Start switch ......................................  32
Throttle lever  ...................................  32
Cooling water pilot outlets  ...............  32
Steering system ...............................  33

Tilt lever  ...........................................  33
Shift lever  ........................................  34
Quick Shift Trim System (QSTS) 

selector ........................................  34

Handgrip ..........................................  36
Reboarding step (for FX Cruiser)  ....  36
Bow eye ...........................................  36
Stern eyes  .......................................  37
Yamaha Engine Management 

System (YEMS)  ...........................  37

Multifunction information center  ......  37
Storage compartments  ....................  43

Operation ......................................... 47

Fuel and oil  ..................................  47

Gasoline ..........................................  47
Engine oil .........................................  48
Filling the fuel tank  ..........................  48

Pre-operation checks  ...................  49

Pre-operation check list  ...................  49
Pre-operation check points ..............  51

Operation .....................................  59

Engine break-in  ...............................  59
Launching the watercraft  .................  59
Starting the engine  ..........................  59
Stopping the engine  ........................  61
Leaving the watercraft  .....................  61

Operating your watercraft  ............  62

Getting to know your watercraft .......  62
Learning to operate your 

watercraft .....................................  62

Riding with passengers  ...................  63
Starting the watercraft  .....................  63
Boarding and starting in deep 

water ............................................  64

Capsized watercraft .........................  67
Turning the watercraft  .....................  68
Stopping the watercraft  ...................  70
Beaching the watercraft ...................  70
Docking the watercraft .....................  70
Reverse on waterways  ....................  70
Rough water operation  ....................  71

UF1Y11E0.book  Page 1  Wednesday, August 23, 2006  11:43 AM

Содержание FX Cruiser WaveRunner 2007













































































































Отзывы:

Нет отзывов