Yamaha F75D Скачать руководство пользователя | Manualshive

Страница: 61 / 75

background image

Trouble Recovery

56

EMU29422

Troubleshooting

A problem in the fuel, compression, or ignition
systems can cause poor starting, loss of pow-
er, or other problems. This section describes
basic checks and possible remedies, and cov-
ers all Yamaha outboard motors. Therefore
some items may not apply to your model.
If your outboard motor requires repair, bring it
to your Yamaha dealer.
If the engine trouble warning indicator is flash-
ing, consult your Yamaha dealer.

Starter will not operate.

Q. Is battery capacity weak or low?
A. Check battery condition. Use battery of rec-
ommended capacity.

Q. Are battery connections loose or corrod-
ed?
A. Tighten battery cables and clean battery
terminals.

Q. Is fuse for electric start relay or electric cir-
cuit blown?
A. Check for cause of electric overload and
repair. Replace fuse with one of correct am-
perage.

Q. Are starter components faulty?
A. Have serviced by a Yamaha dealer.

Q. Is shift lever in gear?
A. Shift to neutral.

Engine will not start (starter operates).

Q. Is fuel tank empty?
A. Fill tank with clean, fresh fuel.

Q. Is fuel contaminated or stale?
A. Fill tank with clean, fresh fuel.

Q. Is fuel filter clogged?
A. Clean or replace filter.

Q. Is starting procedure incorrect?
A. See page 26.

Q. Has fuel pump malfunctioned?
A. Have serviced by a Yamaha dealer.

Q. Are spark plug(s) fouled or of incorrect
type?
A. Inspect spark plug(s). Clean or replace with
recommended type.

Q. Are spark plug cap(s) fitted incorrectly?
A. Check and re-fit cap(s).

Q. Is ignition wiring damaged or poorly con-
nected?
A. Check wires for wear or breaks. Tighten all
loose connections. Replace worn or broken
wires.

Q. Are ignition parts faulty?
A. Have serviced by a Yamaha dealer.

Q. Is engine stop switch lanyard not at-
tached?
A. Attach lanyard.

Q. Are engine inner parts damaged?
A. Have serviced by a Yamaha dealer.

Engine idles irregularly or stalls.

Q. Are spark plug(s) fouled or of incorrect
type?
A. Inspect spark plug(s). Clean or replace with
recommended type.

Q. Is fuel system obstructed?

U6D610E0.book Page 56 Tuesday, April 20, 2004 1:52 PM

«
...
59
60
61
62
63
...
»

Содержание F75D












































































Отзывы:

Нет отзывов

Похожие инструкции для F75D

Бренд: Lantronix Страницы: 10

Бренд: MPS Страницы: 6

Бренд: IEI Technology Страницы: 126

Analog Devices DC2605A

Бренд: Linear Страницы: 16

Бренд: Quantum Страницы: 69

Advanced Socket 370

Бренд: BCM Advanced Research Страницы: 38

Бренд: JETWAY Страницы: 48

Бренд: Texas Instruments Страницы: 17

Бренд: NXP Semiconductors Страницы: 12

Бренд: ASROCK Страницы: 145

Бренд: ST Страницы: 22

Бренд: Aaeon Страницы: 119

Бренд: ASROCK Страницы: 64

Бренд: Biostar Страницы: 31

Бренд: ECS Страницы: 82

Бренд: Gigabyte Страницы: 81

Бренд: Gigabyte Страницы: 18

LCD Programmer Module

Бренд: Xtralis VESDA Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды