Yamaha F75D Скачать руководство пользователя | Manualshive

Страница: 38 / 75

background image

Operation

33

4.

Push the tilt support knob into the clamp
bracket or pull the tilt support lever toward
you to support the engine.

WARNING

EWM00260

After tilting the outboard motor, be sure to
support it with the tilt support knob or tilt
support lever. Otherwise the outboard mo-
tor could fall back down suddenly if oil in
the power trim and tilt unit loses pressure.

5.

Models equipped with trim rods: Once the
outboard motor is supported with the tilt
support lever, press the power trim and
tilt switch “

” (down) to retract the trim

rods.

CAUTION:

ECM00250

Be sure to retract the trim rods completely
during mooring. This protects the rods
from marine growth and corrosion which
could damage the power trim and tilt
mechanism.

EMU28053

Procedure for tilting down

Power trim and tilt models / power tilt models
1.

Push the power tilt / power trim and tilt
switch “

” (up) until the outboard motor

is supported by the tilt rod and the tilt sup-
port lever / tilt support knob becomes
free.

2.

Release the tilt support lever or pull out
the tilt support knob.

3.

Push the power tilt / power trim and tilt
switch “

” (down) to lower the outboard

motor to the desired position.

UP

ZMU04232

DN

ZMU01936

UP

DN

U6D610E0.book Page 33 Tuesday, April 20, 2004 1:52 PM

«
...
36
37
38
39
40
...
»

Содержание F75D












































































Отзывы:

Нет отзывов

Похожие инструкции для F75D

Бренд: Abit Страницы: 112

Бренд: Texas Instruments Страницы: 52

RTKA223012DR0050BU

Бренд: Renesas Страницы: 14

ADRF5515A-EVALZ

Бренд: Analog Devices Страницы: 9

B450M MORTAR TITANIUM

Бренд: MSI Страницы: 144

Бренд: Texas Instruments Страницы: 8

Бренд: Microchip Technology Страницы: 44

Бренд: WynMax Страницы: 68

Бренд: Gigabyte Страницы: 18

Бренд: JETWAY Страницы: 19

K8T8AS - REV 3.0

Бренд: JETWAY Страницы: 26

Бренд: Aaeon Страницы: 111

Бренд: Memec Страницы: 45

Бренд: MSI Страницы: 91

Бренд: OLIMEX Страницы: 17

Бренд: Erreka Страницы: 4

MBD-X11SDV-4C-TP8F-B

Бренд: Supermicro Страницы: 123

BD7F100EFJ-EVK-002

Бренд: Rohm Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды