Yamaha F75D Скачать руководство пользователя | Manualshive

Страница: 50 / 75

background image

Maintenance

45

When fitting the plug, always clean the gasket
surface and use a new gasket. Wipe off any
dirt from the threads and screw in the spark
plug to the correct torque.

NOTE:

If a torque-wrench is not available when you
are fitting a spark plug, a good estimate of the
correct torque is 1/4 to 1/2 a turn past finger-
tight. Have the spark plug adjusted to the cor-
rect torque as soon as possible with a torque-
wrench.

EMU28962

Checking fuel system

WARNING

EWM00060

Gasoline and its vapors are highly flam-
mable and explosive. Keep away from
sparks, cigarettes, flames, or other sourc-
es of ignition.

WARNING

EWM00910

Leaking fuel can result in fire or explosion.

●

Check for fuel leakage regularly.

●

If any fuel leakage is found, the fuel sys-
tem must be repaired by a qualified me-
chanic. Improper repairs can make the
outboard unsafe to operate.

Check the fuel lines for leaks, crack, or mal-
function. If a problem is found, your Yamaha
dealer or other qualified mechanic should re-
pair it immediately.

Checkpoints

●

Fuel system parts leakage

●

Fuel line joint leakage

●

Fuel line cracks or other damage

●

Fuel connector leakage

EMU28980

Inspecting fuel filter

WARNING

EWM00310

Gasoline is highly flammable, and its va-
pors are flammable and explosive.

1. Spark plug gap

2. Spark plug I.D. mark (NGK)

Spark plug gap:

1.0–1.1 mm (0.039–0.043 in)

Spark plug torque:

25.0 Nm (18.4 ft-lb) (2.55 kgf-m)

U6D610E0.book Page 45 Tuesday, April 20, 2004 1:52 PM

«
...
48
49
50
51
52
...
»

Содержание F75D












































































Отзывы:

Нет отзывов

Похожие инструкции для F75D

Бренд: JETWAY Страницы: 46

Бренд: IBM Страницы: 40

Бренд: SOYO Страницы: 95

Бренд: Beck Страницы: 24

Бренд: JETWAY Страницы: 48

Бренд: Avalue Technology Страницы: 82

Бренд: Supero Страницы: 80

DLP LightCrafter Display 3310

Бренд: Texas Instruments Страницы: 16

Бренд: Linear Страницы: 16

Бренд: Avalue Technology Страницы: 80

Бренд: Advantech Страницы: 4

Бренд: ASROCK Страницы: 113

Бренд: Socket Страницы: 37

Бренд: ETOP Страницы: 68

SIDE POWER SRH 240 TC

Бренд: SLEIPNER MOTOR AS Страницы: 28

Бренд: ASROCK Страницы: 92

Бренд: Exar Страницы: 9

Бренд: Asus Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды