Yamaha F75D Скачать руководство пользователя | Manualshive

Страница: 51 / 75

background image

Maintenance

46

●

If you have any question about properly
doing this procedure, consult your
Yamaha dealer.

●

Do not perform this procedure on a hot
or running engine. Allow the engine to
cool.

●

There will be fuel in the fuel filter. Keep
away from sparks, cigarettes, flames or
other sources of ignition.

●

This procedure will allow some fuel to
spill. Catch fuel in a rag. Wipe up any
spilled fuel immediately.

●

The fuel filter must be reassembled
carefully with the O-ring, filter cup, and
hoses in place. Improper assembly or
replacement could result in a fuel leak,
which could result in a fire or explosion
hazard.

EMU30640

Cleaning fuel filter

NOTE:

If any water is in the fuel, the float will rise. If
so, remove the cup and drain the water.

1.

Unscrew the filter cup, catching any
spilled fuel in a rag.

2.

Remove the filter element, and wash it in
solvent. Allow it to dry. Inspect the filter el-
ement and O-ring to make sure they are
in good condition. Replace them if neces-

sary. If any water is found in the fuel, the
Yamaha portable fuel tank or other fuel
tanks should be checked and cleaned.

3.

Reinstall the filter element in the cup.
Make sure the O-ring is in proper position
in the cup. Firmly screw the cup onto the
filter housing.

4.

Attach the filter assembly to the bracket.

5.

Run the engine and check the filter and
lines for leaks.

EMU29040

Inspecting idling speed

WARNING

EWM00450

●

Do not touch or remove electrical parts
when starting or during operation.

●

Keep hands, hair, and clothes away from
the flywheel and other rotating parts
while the engine is running.

●

2-hp models: The propeller rotates
whenever the engine is running. Do not
move the throttle control lever from the
start position during warm-up. The boat
could unexpectedly start to move, which
could result in an accident.

1. Filter cup
2. Filter element

3. O-ring

4. Filter housing
5. Float

1

3

2

4

5

ZMU04269

U6D610E0.book Page 46 Tuesday, April 20, 2004 1:52 PM

«
...
49
50
51
52
53
...
»

Содержание F75D












































































Отзывы:

Нет отзывов

Похожие инструкции для F75D

Бренд: Yamaha Страницы: 20

Бренд: ST Страницы: 24

Airborne WLNN-EK-DP55x

Бренд: B&B Electronics Страницы: 6

VAR-SOM-MX8M-NANO

Бренд: Variscite Страницы: 2

Бренд: AOpen Страницы: 8

Бренд: TYAN Страницы: 47

Бренд: NXP Semiconductors Страницы: 35

Бренд: NXP Semiconductors Страницы: 2

AR6MXCS- Series

Бренд: BCM Страницы: 9

CC85-CC2590EM Series

Бренд: Texas Instruments Страницы: 7

Бренд: ASROCK Страницы: 160

Бренд: u-blox Страницы: 37

Бренд: ASROCK Страницы: 39

Бренд: ASROCK Страницы: 57

PHANTOM GAMING X670E PG Lightning

Бренд: ASROCK Страницы: 66

Бренд: DFI Страницы: 28

Бренд: DFI Страницы: 136

Бренд: SOYO Страницы: 99

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды