Yamaha F75D Скачать руководство пользователя | Manualshive

Страница: 33 / 75

background image

Operation

28

start the engine. The starter can also be
damaged. If the engine will not start after
5 seconds of cranking, return the main
switch to “

” (on), wait 10 seconds,

then crank the engine again.

EMU27670

Warming up engine

EMU30030

Manual start and electric start models

1.

After starting the engine, allow it to idle for
3 minutes to warm up. Failure to do so will
shorten engine life.

2.

Be sure the low oil pressure warning indi-
cator goes off after starting the engine.

3.

Check for a steady flow of water from the
cooling water pilot hole.

CAUTION:

ECM01340

●

If the low oil pressure warning indicator
does not go off after the engine starts,
stop the engine. Otherwise serious en-
gine damage could occur. Check the oil
level and add oil if necessary. Consult
your Yamaha dealer if the cause for the
low oil pressure warning indicator can-
not be found.

●

A continuous flow of water from the pilot
hole shows that the water pump is
pumping water through the cooling pas-
sages. If water is not flowing out of the
pilot hole at all times while the engine is
running, overheating and serious dam-
age could occur. Stop the engine and
check whether the cooling water inlet on
the lower case or the cooling water pilot
hole is blocked. Consult your Yamaha
dealer if the problem cannot be located
and corrected.

●

If the cooling passage is frozen, it may
take awhile for water to start flowing out
of the pilot hole.

EMU27740

Shifting

WARNING

EWM00180

Before shifting, make sure there are no
swimmers or obstacles in the water near
you.

CAUTION:

ECM00220

To change the boat direction or shifting
position from forward to reverse or vice-
versa, first close the throttle so that the en-
gine idles (or runs at low speeds).

EMU27763

Forward (tiller handle and remote
control models)

Tiller control models
1.

Place the throttle grip in the fully closed
position.

2.

Move the gear shift lever quickly and firm-
ly from neutral to forward.

Remote control models
Pull up the neutral interlock trigger (if
equipped) and move the remote control lever
quickly and firmly from neutral to forward.

U6D610E0.book Page 28 Tuesday, April 20, 2004 1:52 PM

«
...
31
32
33
34
35
...
»

Содержание F75D












































































Отзывы:

Нет отзывов

Похожие инструкции для F75D

Бренд: MSI Страницы: 112

Бренд: Zotac Страницы: 54

Бренд: Microchip Technology Страницы: 17

Бренд: A&D Страницы: 4

Бренд: Zida Страницы: 28

Бренд: IBASE Technology Страницы: 84

Бренд: QDI Страницы: 20

Fatal1ty Z87 Killer Series

Бренд: ASROCK Страницы: 102

Бренд: Texas Instruments Страницы: 16

Бренд: Texas Instruments Страницы: 18

Бренд: Gigabyte Страницы: 96

Бренд: Epcom Страницы: 8

Бренд: ASROCK Страницы: 2

Бренд: Supero Страницы: 77

Бренд: Supermicro Страницы: 147

Бренд: TYAN Страницы: 164

Бренд: Biostar Страницы: 40

Бренд: Aaeon Страницы: 123

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды