Yamaha F75D Скачать руководство пользователя | Manualshive

Страница: 32 / 75

background image

Operation

27

2.

Attach the engine stop switch lanyard to
a secure place on your clothing, or your
arm or leg. Then install the lock plate on
the other end of the lanyard into the en-
gine stop switch.

WARNING

EWM00120

●

Attach the engine stop switch lanyard to
a secure place on your clothing, or your
arm or leg while operating.

●

Do not attach the lanyard to clothing
that could tear loose. Do not route the
lanyard where it could become entan-
gled, preventing it from functioning.

●

Avoid accidentally pulling the lanyard
during normal operation. Loss of engine
power means the loss of most steering
control. Also, without engine power, the
boat could slow rapidly. This could
cause people and objects in the boat to
be thrown forward.

3.

Turn the main switch to “

” (on).

NOTE:

Dual engine users: When the main switch is
turned on, the buzzer operates for a few sec-
onds then stops automatically. The buzzer
also operates if one of the engines stalls.

4.

Turn the main switch to “

” (start),

and hold it for a maximum of 5 seconds.

5.

Immediately after the engine starts, re-
lease the main switch to return it to “

”

(on).

CAUTION:

ECM00191

●

Never turn the main switch to “

”

(start) while the engine is running.

●

Do not keep the starter motor turning for
more than 5 seconds. If the starter motor
is turned continuously for more than 5
seconds, the battery will be quickly dis-
charged, thus making it impossible to

ON

START

OFF

ZMU01881

U6D610E0.book Page 27 Tuesday, April 20, 2004 1:52 PM

«
...
30
31
32
33
34
...
»

Содержание F75D












































































Отзывы:

Нет отзывов

Похожие инструкции для F75D

PIC18F57Q43 Curiosity Nano

Бренд: Microchip Technology Страницы: 34

Бренд: Garelick Страницы: 3

Бренд: IBM Страницы: 40

Бренд: SOYO Страницы: 95

Pentium P5I430TX/IIB TITANIUM IIB

Бренд: QDI Страницы: 53

CVN X570 GAMING PRO V14

Бренд: Colorful Страницы: 64

R0K5R8C34DK2HBR

Бренд: Renesas Страницы: 32

Бренд: Ublox Страницы: 38

Advance 10T Series

Бренд: QDI Страницы: 74

Бренд: DFI Страницы: 120

Бренд: Gigabyte Страницы: 18

A20-OLINUXINO-LIME

Бренд: OLIMEX Страницы: 49

Бренд: Biostar Страницы: 37

Бренд: Unicorn Computer Страницы: 36

KEMX-1600 Series

Бренд: Quanmax Страницы: 74

Бренд: Photonic Universe Страницы: 6

Бренд: Gigabyte Страницы: 52

Бренд: Texas Instruments Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды