Yamaha F50F Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 110

background image

Maintenance

88

the screw before installing it.

●

Always use new gaskets. Do not reuse the
removed gaskets.

4. Remove the oil level plug and gasket to

allow the oil to drain completely.

NOTICE:

Check the used gear oil after

it has been drained. If the gear oil is
milky or contains water or a large
amount of metal particles, the gear
case may be damaged. Have a
Yamaha dealer check and repair the
outboard motor.

[ECM00713]

TIP:

For disposal of used oil, consult your
Yamaha dealer.
5. Put the outboard motor in a vertical posi-

tion. Using a flexible or pressurized fill-
ing device, inject the gear oil into the
gear oil drain screw hole.

6. Put a new gasket on the oil level plug.

When the oil begins to flow out of the oil
level plug hole, insert and tighten the oil
level plug.

7. Put a new gasket on the gear oil drain

screw. Insert and tighten the gear oil
drain screw.

EMU29302

Cleaning fuel tank

WARNING

EWM00920

Gasoline is highly flammable, and its va-
pors are flammable and explosive.

●

If you have any question about properly
doing this procedure, consult your
Yamaha dealer.

●

Keep away from sparks, cigarettes,
flames, or other sources of ignition
when cleaning the fuel tank.

●

Remove the fuel tank from the boat be-
fore cleaning it. Work only outdoors in
an area with good ventilation.

●

Wipe up any spilled fuel immediately.

●

Reassemble the fuel tank carefully. Im-

Recommended gear oil:

Hypoid gear oil SAE#90

Gear oil quantity:

F50FEHT 0.430 L
(0.455 US qt, 0.378 Imp.qt)
F50FET 0.430 L
(0.455 US qt, 0.378 Imp.qt)
F60CEHT 0.430 L
(0.455 US qt, 0.378 Imp.qt)
F60CET 0.430 L
(0.455 US qt, 0.378 Imp.qt)
F70AET 0.670 L
(0.708 US qt, 0.590 Imp.qt)
FT60DET 0.670 L
(0.708 US qt, 0.590 Imp.qt)

Tightening torque:

9 Nm (0.9 kgf-m, 6.6 ft-lb)

Tightening torque:

9 Nm (0.9 kgf-m, 6.6 ft-lb)

ZMU03274

6C1-9-26-1E0.book 88 ページ２０１０年２月１０日　水曜日　午後１時５３分

«
...
92
93
94
95
96
...
»

Содержание F50F















































































































Отзывы:

Нет отзывов

Похожие инструкции для F50F

Бренд: Sachs Страницы: 75

Бренд: Rail King Страницы: 46

Бренд: BAFANG Страницы: 6

Бренд: YuanDong Страницы: 23

Cobalt IP Analog

Бренд: DCCconcepts Страницы: 2

Бренд: Grizzly Страницы: 2

Бренд: O.S. engine Страницы: 29

LOMBARDINI 9 LD 625-2

Бренд: Kohler Страницы: 92

AstroTrack 21047

Бренд: ORION TELESCOPES & BINOCULARS Страницы: 2

Бренд: MINN KOTA Страницы: 42

Бренд: Vetus Страницы: 28

Бренд: YS Performance Страницы: 2

Бренд: Electric Drive Engineering Страницы: 19

Бренд: Yanmar Страницы: 248

Бренд: O.S. engine Страницы: 11

Бренд: Yanmar Страницы: 263

Бренд: CHEE SIANG INDUSTRIAL Страницы: 57

Бренд: Kyosho Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды