Yamaha F50F Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 110

background image

32

Instruments and indicators

EMU36014

Indicators

EMU36024

Low oil pressure-alert indicator

If oil pressure drops too low, this indicator will
light up. For further information, see page 43.

NOTICE

ECM00022

●

Do not continue to run the engine if the
low oil pressure-alert indicator is on
and the engine oil level is lower. Seri-
ous engine damage will occur.

●

The low oil pressure-alert indicator
does not indicate the engine oil level.
Use the oil dipstick to check the re-
maining oil quantity. For further infor-
mation, see page 51.

EMU36033

Overheat-alert indicator

If the engine temperature rises too high, this
indicator will light up. For further information
on reading the indicator, see page 43.

NOTICE

ECM00052

Do not continue to run the engine if the
overheat-alert indicator is on. Serious en-
gine damage will occur.

EMU26493

Digital tachometer

The tachometer shows the engine speed
and has the following functions.
All segments of the display will light momen-
tarily after the main switch is turned on and
will return to normal thereafter.

TIP:

The water separator and engine trouble-alert
indicators only operate when the engine is
equipped with the appropriate functions.

1. Low oil pressure-alert indicator

1. Overheat-alert indicator

1. Tachometer
2. Trim meter
3. Hour meter
4. Low oil pressure-alert indicator
5. Overheat-alert indicator
6. Set button
7. Mode button

1

5

2

4

3

6

7

ZMU03601

6C1-9-26-1E0.book 32 ページ２０１０年２月１０日　水曜日　午後１時５３分

«
...
36
37
38
39
40
...
»

Содержание F50F















































































































Отзывы:

Нет отзывов

Похожие инструкции для F50F

Бренд: Barrus Страницы: 97

Бренд: MTD Страницы: 32

PowerBuilt Snow 120000 Series

Бренд: Briggs & Stratton Страницы: 17

Бренд: Briggs & Stratton Страницы: 12

Industrial Plus Snow 90000

Бренд: Briggs & Stratton Страницы: 20

Бренд: Briggs & Stratton Страницы: 10

Бренд: Briggs & Stratton Страницы: 14

Vanguard 490000

Бренд: Briggs & Stratton Страницы: 132

400000 Professional Series

Бренд: Briggs & Stratton Страницы: 92

Бренд: Briggs & Stratton Страницы: 20

200000 Vanguard

Бренд: Briggs & Stratton Страницы: 88

Бренд: Briggs & Stratton Страницы: 9

Бренд: Briggs & Stratton Страницы: 16

Бренд: O.S. engine Страницы: 15

Бренд: FIAMA Страницы: 7

Бренд: RAAMDECORATIE Страницы: 45

Бренд: Baldor Страницы: 2

Бренд: Honda Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды