manualshive.com logo in svg

Yamaha F50F, Руководство пользователя, Страница: 103 / 110

Поделиться
Скачать
Yamaha F50F Скачать руководство пользователя страница 103

Trouble Recovery

97

EMU41470

Water separator-alert indicator blinks 
while cruising

WARNING

EWM01500

Gasoline is highly flammable, and its va-
pors are flammable and explosive.

●

Do not perform this procedure on a hot
or running engine. Allow the engine to
cool.

●

There will be fuel in the fuel filter. Keep
away from sparks, cigarettes, flames or
other sources of ignition.

●

This procedure will allow some fuel to
spill. Catch fuel in a rag. Wipe up any
spilled fuel immediately.

●

The fuel filter must be reassembled
carefully with the O-ring, filter cup, and
hoses in place. Improper assembly or
replacement could result in a fuel leak,
which could result in a fire or explosion
hazard.

If the water separator-alert indicator on the
6Y8 Multifunction tachometer blinks, perform
the following procedure.

F50F, F60C, FT60D
1. Stop the engine.
2. Remove the top cowling.
3. Remove the plastic tie.

4. Disconnect the water detection switch

coupler. 

NOTICE:

 Be careful not to get

any water on the water detection
switch coupler, otherwise a malfunc-
tion could occur.

 [ECM01950]

 

5. Unscrew the filter cup from the filter

housing. 

NOTICE:

 Be careful not to

twist the water detection switch lead
when unscrewing the filter cup.

[ECM01960]

 

1. Water separator-alert indicator

1. Plastic tie

1. Water detection switch coupler

1

ZMU05475

1

ZMU05476

6C1-9-26-1E0.book  97 ページ  ２０１０年２月１０日　水曜日　午後１時５３分

Содержание F50F















































































































Отзывы:

Нет отзывов