Yamaha F50F Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 110

background image

Operation

67

support the engine.

WARNING! After

tilting the outboard motor, be sure to
support it with the tilt support knob or
tilt support lever. Otherwise the out-
board motor could fall back down
suddenly if oil in the power trim and
tilt unit or in the power tilt unit loses
pressure.

[EWM00262]

NOTICE:

Do not use

the tilt support lever or knob when
trailering the boat. The outboard mo-
tor could shake loose from the tilt
support and fall. If the motor cannot
be trailered in the normal running po-
sition, use an additional support de-
vice to secure it in the tilt position.
For more detailed information, see
page 70.

[ECM01641]

4. Models equipped with trim rods: Once

the outboard motor is supported with the
tilt support lever, press the power trim
and tilt switch “

” (down) to retract the

trim rods.

NOTICE:

Make sure that the

trim rods retracts completely during
mooring. This protects the rods from
marine growth and corrosion, which
could damage the power trim and tilt
mechanism.

[ECM00252]

EMU33121

Procedure for tilting down (power
trim and tilt models)

1. Push the power trim and tilt switch “

”

(up) until the outboard motor is support-
ed by the tilt rod and the tilt support lever
becomes free.

2. Release the tilt support lever.

3. Push the power trim and tilt switch “

”

(down) to lower the outboard motor to
the desired position.

ZMU03640

ZMU03644

DN

ZMU01936

UP

DN

DN

ZMU04196

6C1-9-26-1E0.book 67 ページ２０１０年２月１０日　水曜日　午後１時５３分

«
...
71
72
73
74
75
...
»

Содержание F50F















































































































Отзывы:

Нет отзывов

Похожие инструкции для F50F

Бренд: O.S. engine Страницы: 4

Бренд: Beta Marine Страницы: 88

Бренд: Wacker Neuson Страницы: 70

E-8 DIESEL ENGINE

Бренд: M.T.H. Страницы: 36

Бренд: Polini Страницы: 32

Бренд: Vanguard Страницы: 120

Бренд: Bosch Страницы: 106

rexroth MSK 030

Бренд: Bosch Страницы: 72

Rexroth MKE Series

Бренд: Bosch Страницы: 134

Бренд: Bosch Страницы: 82

Бренд: Bosch Страницы: 124

Rexroth MKE E Series

Бренд: Bosch Страницы: 138

Бренд: Zenoah Страницы: 4

AG2210-LP Series

Бренд: Beckhoff Страницы: 35

Бренд: Chamberlain Страницы: 20

Бренд: Chamberlain Страницы: 28

Бренд: Robin America Страницы: 36

Бренд: Yanmar Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды