Yamaha F50F Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 110

background image

Instruments and indicators

36

EMU36080

Voltmeter

The voltmeter displays the charge of the bat-
tery in volts(V).

EMU26721

Fuel level-alert indicator

If the fuel level decreases to one segment,
the fuel level alert segment will blink.
Do not continue to operate the engine with
full throttle if an alert device has activated.
Get back to the port within trolling engine
speed.

NOTICE:

Running out of fuel can

damage the engine.

[ECM01770]

EMU26732

Low battery voltage-alert indicator

If battery voltage drops, the display will auto-
matically turn on and blink.
Get back to the port soon if an alert device
has activated. For charging the battery, con-
sult your Yamaha dealer.

EMU26471

Analog tachometer

This gauge shows the engine speed and has
the following functions.

EMU26506

Low oil pressure-alert indicator

If oil pressure drops too low, this indicator will
flash. For further information, see page 43.

NOTICE

ECM00022

●

Do not continue to run the engine if the
low oil pressure-alert indicator is on
and the engine oil level is lower. Seri-
ous engine damage will occur.

●

The low oil pressure-alert indicator
does not indicate the engine oil level.

1. Fuel level-alert segment

1. Low battery indicator

1. Tachometer
2. Alert indicator(s)

ZMU04578

1

2

6C1-9-26-1E0.book 36 ページ２０１０年２月１０日　水曜日　午後１時５３分

«
...
40
41
42
43
44
...
»

Содержание F50F















































































































Отзывы:

Нет отзывов

Похожие инструкции для F50F

Command Pro CH940-CH1000

Бренд: Kohler Страницы: 16

MICROPUMP EagleDrive MS

Бренд: Idex Страницы: 23

Бренд: Toro Страницы: 62

Бренд: Texas Equipment Страницы: 38

Бренд: Volvo Страницы: 88

Бренд: Wilesco Страницы: 4

Бренд: Wilesco Страницы: 2

Бренд: Wilesco Страницы: 4

Бренд: Wilesco Страницы: 4

Бренд: Wilesco Страницы: 4

Бренд: Wilesco Страницы: 4

Бренд: Wren Turbines Страницы: 13

Бренд: Wren Turbines Страницы: 40

Бренд: Wyco Страницы: 26

Бренд: Westerbeke Страницы: 6

Бренд: Iveco Страницы: 74

Бренд: Royal Enfield Страницы: 152

Бренд: ZIEHL-ABEGG Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды