Yamaha F50F Скачать руководство пользователя страница 29

Страница: 29 / 110

Components

lever.

TIP:

●

The free accelerator button can only be
pushed when the remote control lever is in
the neutral position.

●

After the button is pushed, the throttle be-
gins to open after the remote control lever
is moved at least 35



●

After using the free accelerator, return the
remote control lever to the neutral position.
The free accelerator button will return au-
tomatically to its set position. The remote
control will then engage forward and re-
verse normally.

EMU25912

Tiller handle

To change direction, move the tiller handle to
the left or right as necessary.

EMU25923

Gear shift lever

Move the gear shift lever forward to engage
the forward gear or rearward to engage the
reverse gear.

EMU25941

Throttle grip

The throttle grip is on the tiller handle. Turn
the grip counterclockwise to increase speed
and clockwise to decrease speed.

1. Fully open
2. Fully closed
3. Free accelerator

ZMU04576

1. Forward “ ”
2. Neutral “ ”
3. Reverse “ ”

6C1-9-26-1E0.book 23 ページ２０１０年２月１０日　水曜日　午後１時５３分

Содержание F50F















































































































Результаты поиска

Содержание F50F

Отзывы:

Похожие инструкции для F50F

Бренды по названию

Популярные бренды

Yamaha F50F, Руководство пользователя

Результаты поиска

Содержание F50F

Отзывы:

Похожие инструкции для F50F

Бренды по названию

Популярные бренды