Yamaha F20G страница 30 Скачать руководство пользователя | Manualshive

Страница: 30 / 108

background image

Components

24

EMU25978

Throttle friction adjuster

A friction device provides adjustable resis-
tance to movement of the throttle grip or the
remote control lever, and can be set accord-
ing to operator preference.
To increase resistance, turn the adjuster
clockwise. To decrease resistance, turn the
adjuster counterclockwise.

WARNING! Do

not overtighten the friction adjuster. If
there is too much resistance, it could be
difficult to move the remote control lever
or throttle grip, which could result in an
accident.

[EWM00033]

When constant speed is desired, tighten the
adjuster to maintain the desired throttle set-
ting.

EMU25996

Engine shut-off cord (lanyard) and
clip

The clip must be attached to the engine shut-
off switch for the engine to run. The cord
should be attached to a secure place on the
operator’s clothing, or arm or leg. Should the
operator fall overboard or leave the helm, the
cord will pull out the clip, stopping ignition to
the engine. This will prevent the boat from
running away under power.

WARNING! At-

tach the engine shut-off cord to a secure
place on your clothing, or your arm or leg
while operating. Do not attach the cord to
clothing that could tear loose. Do not
route the cord where it could become en-
tangled, preventing it from functioning.

1. Throttle indicator

1

1

1

ZMU03169

ZMU08725

6HY-9-71-1E0.book 24 ページ２０１９年１２月４日　水曜日　午後２時５１分

«
...
28
29
30
31
32
...
»

Содержание F20G













































































































Отзывы:

Нет отзывов

Похожие инструкции для F20G

Бренд: Texas Instruments Страницы: 52

AIMB-562 series

Бренд: Advantech Страницы: 59

Бренд: Linear Technology Страницы: 16

Бренд: C&T Solution Страницы: 84

Бренд: ST Страницы: 24

Бренд: ST Страницы: 15

Бренд: MSI Страницы: 91

Бренд: ASROCK Страницы: 226

tKINO-AL-E1-R10

Бренд: IEI Technology Страницы: 12

Бренд: ZMDI Страницы: 25

Outboard Motor BF5A

Бренд: Honda Страницы: 84

ISOFACE ISO2H823V2

Бренд: Infineon Страницы: 28

Бренд: Advantech Страницы: 88

Бренд: Foxconn Страницы: 111

Бренд: Gigabyte Страницы: 88

Бренд: NXP Semiconductors Страницы: 19

Бренд: Quantum Design Страницы: 59

Бренд: Quantum Design Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды