Yamaha F20G страница 23 Скачать руководство пользователя | Manualshive

Страница: 23 / 108

background image

Specifications and requirements

17

Gasohol

There are two types of gasohol: gasohol con-
taining ethanol (E5 and E10) and that con-
taining methanol. Ethanol can be used if the
ethanol content does not exceed 10% and
the fuel meets the minimum octane ratings.
E85 is a fuel containing 85% ethanol and
must not be used in your outboard motor. All
ethanol blends containing more than 10%
ethanol can cause fuel system damage or
cause engine starting and running problems.
Yamaha does not recommend gasohol con-
taining methanol because it can cause fuel
system damage or engine performance
problems.
It is recommended that you install a water-
separating marine fuel filter assembly (10 mi-
cron minimum) between your boat’s fuel tank
and outboard motor when using ethanol.
Ethanol is known to allow moisture to be ab-
sorbed into boat fuel tanks and systems.
Moisture in the fuel can cause corrosion of
metallic fuel system components, starting
and running complaints and require addition-
al fuel system maintenance.

EMU36881

Muddy or acidic water

Yamaha strongly recommends that you have
your dealer install the optional chromium-
plated water pump kit if you use the outboard
motor in muddy or acidic water conditions.
However, depending on the model it might
not be required.

EMU36331

Anti-fouling paint

A clean hull improves boat performance. The
boat bottom should be kept as clean of ma-
rine growth as possible. If necessary, the
boat bottom can be coated with an anti-foul-
ing paint approved for your area to inhibit

marine growth.
Do not use anti-fouling paint which includes
copper or graphite. These paints can cause
more rapid engine corrosion.

EMU40302

Outboard motor disposal

requirements

Never illegally discard (dump) the outboard
motor. Yamaha recommends consulting the
dealer about discarding the outboard motor.

EMU36353

Emergency equipment

Keep the following items onboard in case
there is trouble with the outboard motor.



A tool kit with assorted screwdrivers, pli-
ers, wrenches (including metric sizes), and
electrical tape.



Waterproof flashlight with extra batteries.



An extra engine shut-off cord (lanyard)
with clip.



Spare parts, such as an extra set of spark
plugs.

Consult your Yamaha dealer for details.

6HY-9-71-1E0.book 17 ページ２０１９年１２月４日　水曜日　午後２時５１分

«
...
21
22
23
24
25
...
»

Содержание F20G













































































































Отзывы:

Нет отзывов

Похожие инструкции для F20G

Бренд: Lantronix Страницы: 17

Бренд: MSI Страницы: 35

Бренд: Linear Technology Страницы: 16

KEEX-1850 Series

Бренд: Quanmax Страницы: 61

Бренд: Gan Systems Страницы: 28

ML501MicroBlaze

Бренд: Xilinx Страницы: 46

Бренд: Zotac Страницы: 56

Бренд: ASROCK Страницы: 2

TITAN TURBO PLUS ATX

Бренд: TYAN Страницы: 69

Бренд: XFX Страницы: 120

Бренд: DFI Страницы: 107

ADIS1650 PCBZSeries

Бренд: Analog Devices Страницы: 11

Бренд: Acorp Страницы: 4

Бренд: Avalue Technology Страницы: 29

Бренд: Gigabyte Страницы: 96

Spacewalker AV40

Бренд: Shuttle Страницы: 81

Бренд: JETWAY Страницы: 60

Бренд: BCM Advanced Research Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды