Yamaha F20G страница 28 Скачать руководство пользователя

Страница: 28 / 108

Components

EMU26202

Neutral interlock trigger

To shift out of neutral, first pull the neutral in-
terlock trigger up.

EMU26213

Neutral throttle lever

To open the throttle without shifting into ei-
ther forward or reverse, put the remote con-
trol lever in the neutral position and lift the
neutral throttle lever.

TIP:

The neutral throttle lever will operate only
when the remote control lever is in neutral.
The remote control lever will operate only

when the neutral throttle lever is in the closed
position.

EMU25914

Tiller handle

To change direction, move the tiller handle to
the left or right as necessary.

EMU25925

Gear shift lever

Move the gear shift lever forward to engage
the forward gear or rearward to engage the
reverse gear.

6. Throttle
7. Fully open

1. Neutral interlock trigger

1. Fully open
2. Fully closed

ZMU01727

ZMU01728

ZMU08721

6HY-9-71-1E0.book 22 ページ２０１９年１２月４日　水曜日　午後２時５１分

Содержание F20G













































































































Результаты поиска

Содержание F20G

Отзывы:

Похожие инструкции для F20G

Бренды по названию

Популярные бренды

Yamaha F20G, Руководство пользователя

Результаты поиска

Содержание F20G

Отзывы:

Похожие инструкции для F20G

Бренды по названию

Популярные бренды