Yamaha F20G страница 5 Скачать руководство пользователя

Страница: 5 / 108

Table of contents

Power tilt unit..................................... 30
Cowling lock lever ............................. 30
Flushing device ................................. 31
Alert indicator ................................... 31

Instruments and indicators ............ 32

Indicators ....................................... 32

Low oil pressure-alert indicator ......... 32
Overheat-alert indicator..................... 32

Engine control system.................... 33

Alert system ................................... 33

Overheat alert.................................... 33
Low oil pressure alert ........................ 33

Installation ....................................... 35

Installation ...................................... 35

Mounting the outboard motor ............ 35
Clamping the outboard motor............ 37

Operation ......................................... 39

First-time operation ........................ 39

Fill engine oil ..................................... 39
Breaking in engine............................. 39
Getting to know your boat ................. 39

Checks before starting engine ....... 39

Filling fuel ...................................... 44
Operating engine............................ 45

Sending fuel (portable tank) .............. 45
Starting engine .................................. 46

Checks after starting engine .......... 51

Cooling water .................................... 51

Warming up engine........................ 51

Manual start and electric start

models ........................................... 51

Checks after engine warm up ........ 52

Shifting .............................................. 52
Stop switches .................................... 52

Shifting ........................................... 52
Stopping boat................................. 54
Trolling ........................................... 54

Adjusting trolling speed ..................... 54

Stopping engine............................. 54

Procedure.......................................... 55

Trimming outboard motor............... 56

Adjusting trim angle for manual tilt

models ........................................... 56

Adjusting trim angle (power tilt

models) .......................................... 57

Adjusting boat trim............................. 58

Tilting up and down........................ 58

Procedure for tilting up (manual tilt

models) .......................................... 59

Procedure for tilting up (power tilt

models) .......................................... 60

Procedure for tilting down (manual

tilt models)...................................... 61

Procedure for tilting down (power

tilt models)...................................... 62

Shallow water ................................ 62

Cruising in shallow water (manual

tilt models)...................................... 62

Power tilt models ............................... 64

Cruising in other conditions............ 65

Maintenance .................................... 66

Transporting and storing outboard

motor........................................... 66

Dismounting the outboard motor ....... 66
Storing outboard motor...................... 68
Procedure.......................................... 68
Lubrication......................................... 69
Flushing power unit ........................... 70
Cleaning the outboard motor............. 71
Checking painted surface of

outboard motor............................... 71

6HY-9-71-1E0.book 2 ページ２０１９年１２月４日　水曜日　午後２時５１分

Содержание F20G













































































































Результаты поиска

Содержание F20G

Отзывы:

Похожие инструкции для F20G

Бренды по названию

Популярные бренды

Yamaha F20G, Руководство пользователя

Результаты поиска

Содержание F20G

Отзывы:

Похожие инструкции для F20G

Бренды по названию

Популярные бренды