Yamaha F20G страница 68 Скачать руководство пользователя | Manualshive

Страница: 68 / 108

background image

Operation

62

EMU44620

Procedure for tilting down (power tilt
models)

(1) Push the power tilt switch “

” (up) until

the outboard motor is supported by the
tilt rod and the tilt support knob becomes
free.

(2) Pull out the tilt support knob.

(3) Push the power tilt switch “

” (down) to

lower the outboard motor to the desired
position.

EMU28063

Shallow water

EMU28074

Cruising in shallow water (manual tilt
models)

EWM01782



Run the boat at the lowest possible
speed when using the shallow water
cruising system. The tilt lock mecha-
nism does not work while the shallow
water cruising system is being used.
Hitting an underwater obstacle could
cause the outboard motor to lift out of
the water, resulting in loss of control.



Use extra care when operating in re-
verse. Too much reverse thrust can
cause the outboard motor to lift out of
the water, increasing the chance of ac-
cident and personal injury.

ECM00261

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-
ing can result.

ZMU0

8

77

3

DN

ZMU01936

UP

DN

DN

ZMU08774

6HY-9-71-1E0.book 62 ページ２０１９年１２月４日　水曜日　午後２時５１分

«
...
66
67
68
69
70
...
»

Содержание F20G













































































































Отзывы:

Нет отзывов

Похожие инструкции для F20G

Бренд: AXIOMTEK Страницы: 2

Бренд: Linear Technology Страницы: 6

Бренд: Ublox Страницы: 23

1stMainboard VG33

Бренд: FIC Страницы: 38

Бренд: ST Страницы: 77

Бренд: Texas Instruments Страницы: 9

Бренд: Gigabyte Страницы: 116

Бренд: Texas Instruments Страницы: 21

tps61040EVM-002

Бренд: Texas Instruments Страницы: 31

Бренд: Global American Страницы: 37

Бренд: Gigabyte Страницы: 93

Бренд: Vox Страницы: 93

Бренд: Embedian Страницы: 70

Бренд: Gigabyte Страницы: 44

Бренд: Gigabyte Страницы: 96

Бренд: Advantech Страницы: 136

Бренд: ECS Страницы: 131

S2257 THUNDER 2400

Бренд: TYAN Страницы: 105

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды