manualshive.com logo in svg

Yamaha F20G, Руководство пользователя

Поделиться
Скачать
Yamaha F20G Скачать руководство пользователя страница 94

Maintenance

88

level plug.

TIP:

Apply a light coat of gear oil to the oil level
plug thread and gasket before installation.

(7) Put a new gasket on the gear oil drain

screw. Insert and tighten the gear oil
drain screw.

TIP:

Apply a light coat of gear oil to the gear oil
drain screw thread and gasket before instal-
lation.

EMU29318

Inspecting and replacing anode(s)

Yamaha outboard motors are protected from
corrosion by sacrificial anodes. Inspect the
external anodes periodically. Remove scales
from the surfaces of the anodes. Consult a
Yamaha dealer for replacement of external
anodes.

ECM00721

Do not paint anodes, as this would render
them ineffective.

TIP:

Inspect ground leads attached to external
anodes on equipped models. Consult a
Yamaha dealer for inspection and replace-
ment of internal anodes attached to the pow-
er unit.

EMU29324

Checking battery (for electric start 
models)

EWM01903

Battery electrolyte is poisonous and
caustic, and batteries generate explosive
hydrogen gas. When working near the
battery:

Wear protective eye gear and rubber
gloves.

Do not smoke or bring any other source
of ignition near the battery.

The procedure for checking the battery var-

Tightening torque:

7 N·m (0.7 kgf·m, 5.2 lb·ft)

Tightening torque:

7 N·m (0.7 kgf·m, 5.2 lb·ft)

ZMU02924

ZMU05024

6HY-9-71-1E0.book  88 ページ  ２０１９年１２月４日　水曜日　午後２時５１分

Содержание F20G













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды