Yamaha Electone 115D Скачать руководство пользователя страница 51

Страница: 51 / 81

Maintenance

EMU28521

Maintenance chart

Frequency of maintenance operations may be adjusted according to the operating condi-
tions, but the following table gives general guidelines. Refer to the sections in this chapter for
explanations of each owner-specific action.
The “

” symbol indicates the check-ups which you may carry out yourself.

The “

” symbol indicates work to be carried out by your Yamaha dealer.

Item

Actions

Initial

Every

10 hours

(1 month)

50 hours

months)

100

hours (6
months)

200

hours (1

year)

Anode(s) (external)

Inspection / replace-
ment

Anode(s) (internal)

Inspection / replace-
ment

Battery

Inspection / charging

Cooling water pas-
sages

Cleaning

Cowling clamp

Inspection

Fuel filter (can be dis-
assembled)

Inspection / cleaning

Fuel system

Inspection

Gear oil

Change

Greasing points

Greasing

Idling speed (carbure-
tor models)

Inspection / adjustment

PCV (Pressure Con-
trol Valve)

Inspection

Power trim and tilt unit

Inspection

Propeller and cotter pin

Inspection / replace-
ment

Shift link / shift cable

Inspection / adjustment

Thermostat

Inspection

Throttle link / throttle
cable / throttle pick-up
timing

Inspection / adjustment

Water pump

Inspection

Oil pump

Inspection / adjustment

Oil tank water drain

Inspection / cleaning

www.reelschematic.com

Содержание Electone 115D


















































































Результаты поиска

Содержание Electone 115D

Отзывы:

Похожие инструкции для Electone 115D

Бренды по названию

Популярные бренды

Yamaha Electone 115D, Руководство пользователя

Результаты поиска

Содержание Electone 115D

Отзывы:

Похожие инструкции для Electone 115D

Бренды по названию

Популярные бренды