Yamaha Electone 115D Скачать руководство пользователя страница 22

Страница: 22 / 81

Basic components

EMU26540

Oil level indicators (three indicators)

The indicators on the gauge show the status
of the oil level. For details on how to read the
indicators, see page 29.

CAUTION:

ECM00030

Do not operate the engine without oil. Se-

rious engine damage will occur.

EMU26550

Oil level indicator (digital type)

This indicator shows the engine oil level. If
the oil level falls below the lower limit, the
warning indicator will start to blink. For fur-
ther information, see page 22.

CAUTION:

ECM00030

Do not operate the engine without oil. Se-

rious engine damage will occur.

EMU26581

Overheat warning indicator (digital
type)

If the engine temperature rises too high, the
warning indicator will start to blink. For fur-
ther information on reading the indicator, see
page 21.

CAUTION:

ECM00050

Do not continue to run the engine if the
overheat warning indicator is on. Serious

engine damage will occur.

EMU26600

Speedometer (digital type)

This gauge shows the boat speed.

1. Oil level indicators

ZMU04580

1. Oil level indicator

1. Overheat warning indicator

ZMU01867

ZMU01868

www.reelschematic.com

Содержание Electone 115D


















































































Результаты поиска

Содержание Electone 115D

Отзывы:

Похожие инструкции для Electone 115D

Бренды по названию

Популярные бренды

Yamaha Electone 115D, Руководство пользователя

Результаты поиска

Содержание Electone 115D

Отзывы:

Похожие инструкции для Electone 115D

Бренды по названию

Популярные бренды