Yamaha Electone 115D Скачать руководство пользователя страница 20

Страница: 20 / 81

Basic components

EMU26340

Tilt support lever for power trim and
tilt or hydro tilt model

To keep the outboard motor in the tilted up
position, lock the tilt support lever to the
clamp bracket.

EMU26400

Top cowling release lever

The top cowling can be removed by operat-
ing the cowling release lever. Pulling the
front lever unlocks the top cowling for remov-
al.

When installing the top cowling:
1.

Set the top cowling straight down onto
the engine, being careful to avoid catch-
ing spark plug wires or other wires.

Align the three cowling hooks with the
locks on the bottom cowling.

Press down on the top of the cowling at
the front and both sides of the back until
the three locks click.

To make sure the cowling is locked
properly push the cowling from each
side. If it lifts, repeat step 3.

CAUTION:

ECM00070

●

Make sure the cowling lock connection

1. Trim tab
2. Bolt
3. Cap

1. Tilt support lever

ZMU02525

ZMU01863

ZMU03979

ZMU03518

ZMU03519

www.reelschematic.com

Содержание Electone 115D


















































































Результаты поиска

Содержание Electone 115D

Отзывы:

Похожие инструкции для Electone 115D

Бренды по названию

Популярные бренды

Yamaha Electone 115D, Руководство пользователя

Результаты поиска

Содержание Electone 115D

Отзывы:

Похожие инструкции для Electone 115D

Бренды по названию

Популярные бренды