Yamaha Electone 115D Скачать руководство пользователя страница 43

Страница: 43 / 81

Operation

EMU28060

Cruising in shallow water

The outboard motor can be tilted up partially
to allow operation in shallow water.

EMU28090

Power trim and tilt models / power tilt
models

The outboard motor can be tilted up partially
to allow operation in shallow water.

WARNING

EWM00660

●

Place the gear shift in neutral before
setting up for shallow water cruising.

●

Return the outboard motor to its normal
position as soon as the boat is back in

deeper water.

CAUTION:

ECM00260

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-

ting up for and cruising in shallow water.
Otherwise severe damage from overheat-

ing can result.

EMU28183

Procedure for power trim and tilt / power
tilt models

Place the gear shift lever in neutral.

Slightly tilt the outboard motor up to the
desired position using the power trim / tilt
switch.

To return the outboard motor to the nor-

ZMU01936

ZMU04147

ZMU01935

ZMU04146

www.reelschematic.com

Содержание Electone 115D


















































































Результаты поиска

Содержание Electone 115D

Отзывы:

Похожие инструкции для Electone 115D

Бренды по названию

Популярные бренды

Yamaha Electone 115D, Руководство пользователя

Результаты поиска

Содержание Electone 115D

Отзывы:

Похожие инструкции для Electone 115D

Бренды по названию

Популярные бренды