Yamaha Electone 115D Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 81

background image

Basic components

11

EMU26190

Remote control lever

Moving the lever forward from the neutral po-
sition engages forward gear. Pulling the le-
ver back from neutral engages reverse. The
engine will continue to run at idle until the le-
ver is moved about 35° (a detent can be felt).
Moving the lever farther opens the throttle,
and the engine will begin to accelerate.

EMU26201

Neutral interlock trigger

To shift out of neutral, first pull the neutral in-
terlock trigger up.

EMU26211

Neutral throttle lever

To open the throttle without shifting into ei-
ther forward or reverse, put the remote con-
trol lever in the neutral position and lift the
neutral throttle lever.

NOTE:

The neutral throttle lever will operate only
when the remote control lever is in neutral.
The remote control lever will operate only
when the neutral throttle lever is in the closed

position.

1. Power trim and tilt switch
2. Remote control lever
3. Neutral interlock trigger
4. Neutral throttle lever
5. Main switch / choke switch
6. Engine stop lanyard switch
7. Throttle friction adjuster

1. Neutral “ ”

2. Forward “ ”

3. Reverse “ ”
4. Shift
5. Fully closed

6. Throttle
7. Fully open

1. Neutral interlock trigger

www.reelschematic.com

«
...
14
15
16
17
18
...
»

Содержание Electone 115D


















































































Отзывы:

Нет отзывов

Похожие инструкции для Electone 115D

Sound Wave 115S

Бренд: Ibanez Страницы: 2

Бренд: Kawai Страницы: 22

Concert Performer CP3

Бренд: Kawai Страницы: 40

Бренд: Kawai Страницы: 36

Бренд: Kawai Страницы: 148

Бренд: Kawai Страницы: 30

Classic Series CS6

Бренд: Kawai Страницы: 96

Бренд: Katronic Страницы: 3

FLUXUS ADM 6725

Бренд: Katronic Technologies Страницы: 148

Бренд: Kawai Страницы: 176

Бренд: Waterproof Страницы: 10

Бренд: Ocean Optics Страницы: 43

Бренд: Ocean Technology Systems Страницы: 12

Бренд: Ocean Reef Страницы: 24

Бренд: Vega Страницы: 28

Бренд: Vega Страницы: 20

Бренд: Unitech Страницы: 18

Veeder-Root 7990 Series

Бренд: Danaher Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды