background image

 

Basic components

 

12

 

EMU26221

 

Choke switch

 

To activate the choke system, press in the
main switch while the key is turned to the

” (on) or “

” (start) position. The

choke system will then supply the rich fuel
mixture required to start the engine. When
the key is released, the choke will switch off
automatically.

 

EMU25970

 

Throttle friction adjuster

 

A friction device provides adjustable resis-
tance to movement of the throttle grip or the
remote control lever, and can be set accord-
ing to operator preference.
To increase resistance, turn the adjuster
clockwise. To decrease resistance, turn the

adjuster counterclockwise.

WARNING

 

EWM00030 

 

Do not overtighten the friction adjuster. If
there is too much resistance, it could be
difficult to move throttle lever or grip,

 

which could result in an accident.

 

When constant speed is desired, tighten the
adjuster to maintain the desired throttle set-
ting.

 

EMU25990

 

Engine stop lanyard switch

 

The lock plate must be attached to the en-
gine stop switch for the engine to run. The
lanyard should be attached to a secure place
on the operator’s clothing, or arm or leg.
Should the operator fall overboard or leave
the helm, the lanyard will pull out the lock
plate, stopping ignition to the engine. This
will prevent the boat from running away un-
der power.

WARNING

 

EWM00120 

 

 

Attach the engine stop switch lanyard
to a secure place on your clothing, or
your arm or leg while operating.

 

 

Do not attach the lanyard to clothing
that could tear loose. Do not route the
lanyard where it could become entan-
gled, preventing it from functioning.

 

 

Avoid accidentally pulling the lanyard

 

1. Fully open
2. Fully closed

ZMU03160

www.reelschematic.com

Содержание Electone 115D


















































































Отзывы: