Yamaha DragStar XVS650A Скачать руководство пользователя страница 66

Страница: 66 / 86

PERIODIC MAINTENANCE AND MINOR REPAIR

6-29

EAU24281

Replacing a turn signal light
bulb or the tail/brake light bulb

1. Remove the lens by removing the

screws.

2. Remove the defective bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by installing the

screws.

CAUTION:

ECA10680

Do not overtighten the screws, oth-
erwise the lens may break.

EAU33411

Replacing the auxiliary light
bulb

If the auxiliary light bulb burns out, re-
place it as follows.

1. Remove the headlight unit by re-

moving the screws.

2. Remove the socket (together with

the bulb) by pushing it in and turn-
ing it counterclockwise.

1. Screw

U5SCE1E0.book Page 29 Monday, September 8, 2003 11:32 AM

Содержание DragStar XVS650A























































































Результаты поиска

Содержание DragStar XVS650A

Отзывы:

Похожие инструкции для DragStar XVS650A

Бренды по названию

Популярные бренды

Yamaha DragStar XVS650A, Руководство пользователя

Результаты поиска

Содержание DragStar XVS650A

Отзывы:

Похожие инструкции для DragStar XVS650A

Бренды по названию

Популярные бренды