Yamaha DragStar XVS650A Скачать руководство пользователя | Manualshive

Страница: 48 / 86

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-11

6

EAU33380

Cleaning the air filter element

The air filter element should be cleaned
at the intervals specified in the periodic
maintenance and lubrication chart.
Clean the air filter element more fre-
quently if you are riding in unusually
wet or dusty areas.

1. Remove the air filter case cover by

removing the screws.

2. Pull the air filter element out.
3. Lightly tap the air filter element to

remove most of the dust and dirt,
and then blow the remaining dirt
out with compressed air as shown.
If the air filter element is damaged,
replace it.

4. Insert the air filter element into the

air filter case as shown.

CAUTION:

ECA10480

●

Make sure that the air filter ele-
ment is properly seated in the
air filter case.

●

The engine should never be op-
erated without the air filter ele-
ment installed, otherwise the
piston(s) and/or cylinder(s) may
become excessively worn.

5. Install the air filter case cover by

aligning the match marks and in-
stalling the screws.

1. Air filter case cover

2. Screw

1. Air filter element

1. Air filter element holder

2. Projection
3. Slot

1. Match marks

U5SCE1E0.book Page 11 Monday, September 8, 2003 11:32 AM

«
...
46
47
48
49
50
...
»

Содержание DragStar XVS650A























































































Отзывы:

Нет отзывов

Похожие инструкции для DragStar XVS650A

Бренд: Razor Страницы: 2

Бренд: Öhlins Страницы: 8

prodrive SUR 3A00

Бренд: Öhlins Страницы: 4

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 8

Бренд: Öhlins Страницы: 4

Бренд: Yamaha Страницы: 568

Бренд: SCHUBERTH Страницы: 41

Бренд: Lakeland Страницы: 16

Бренд: B&G electronics Страницы: 5

Бренд: TB Страницы: 8

Бренд: Honda Страницы: 130

Бренд: Crivit Страницы: 30

Бренд: Wolfman Страницы: 3

Бренд: Honda Страницы: 161

Бренд: Honda Страницы: 224

California EV V1100

Бренд: MOTO GUZZI Страницы: 173

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды