Yamaha DragStar XVS650A Скачать руководство пользователя

Страница: 54 / 86

PERIODIC MAINTENANCE AND MINOR REPAIR

6-17

7. Tighten the locknut at the clutch le-

ver and the crankcase.

EAU22092

Adjusting the brake lever free
play

The brake lever free play should mea-
sure 10.0–15.0 mm (0.39–0.59 in) as
shown. Periodically check the brake le-
ver free play and, if necessary, adjust it
as follows.

1. Loosen the locknut at the brake le-

ver.

2. To increase the brake lever free

play, turn the adjusting screw in di-
rection (a). To decrease the brake
lever free play, turn the adjusting
screw in direction (b).

3. Tighten the locknut.

WARNING

EWA10630

●

After adjusting the brake lever
free play, check the free play
and make sure that the brake is
working properly.

●

A soft or spongy feeling in the
brake lever can indicate the
presence of air in the hydraulic

1. Brake lever free play

1. Locknut
2. Brake lever free play adjusting screw

U5SCE1E0.book Page 17 Monday, September 8, 2003 11:32 AM

Содержание DragStar XVS650A























































































Результаты поиска

Содержание DragStar XVS650A

Отзывы:

Похожие инструкции для DragStar XVS650A

Бренды по названию

Популярные бренды

Yamaha DragStar XVS650A, Руководство пользователя

Результаты поиска

Содержание DragStar XVS650A

Отзывы:

Похожие инструкции для DragStar XVS650A

Бренды по названию

Популярные бренды