Yamaha DragStar XVS650A Скачать руководство пользователя страница 55

Страница: 55 / 86

PERIODIC MAINTENANCE AND MINOR REPAIR

6-18

system. If there is air in the hy-
draulic system, have a Yamaha
dealer bleed the system before
operating the motorcycle. Air in
the hydraulic system will dimin-
ish the braking performance,
which may result in loss of con-
trol and an accident.

EAU22231

Adjusting the brake pedal
position and free play

WARNING

EWA10670

It is advisable to have a Yamaha
dealer make these adjustments.

NOTE:

The brake pedal position should be ad-
justed before adjusting the brake pedal
free play.

Brake pedal position

The brake pedal should be positioned
approximately 108.0 mm (4.25 in)
above the top of the footrest as shown.

Periodically check the brake pedal po-
sition and, if necessary, adjust it as fol-
lows.

1. Loosen the locknut at the brake

pedal.

2. To raise the brake pedal, turn the

adjusting bolt in direction (a). To
lower the brake pedal, turn the ad-
justing bolt in direction (b).

3. Tighten the locknut.

WARNING

EWA11230

After adjusting the brake pedal posi-
tion, the brake pedal free play must
be adjusted.

1. Distance between brake pedal and footrest

2. Brake pedal free play

1. Locknut
2. Brake pedal position adjusting bolt

U5SCE1E0.book Page 18 Monday, September 8, 2003 11:32 AM

Содержание DragStar XVS650A























































































Результаты поиска

Содержание DragStar XVS650A

Отзывы:

Похожие инструкции для DragStar XVS650A

Бренды по названию

Популярные бренды

Yamaha DragStar XVS650A, Руководство пользователя

Результаты поиска

Содержание DragStar XVS650A

Отзывы:

Похожие инструкции для DragStar XVS650A

Бренды по названию

Популярные бренды